We have used linear one-dimensional elements to approximate the temperature distribution along a fin. The nodal temperatures and their corresponding positions are shown in Fig. 4. What is the temperature of the fin at (a) X-4cm ( and (b) X 8cm

We have used linear one-dimensional elements to approximate the temperature distribution along a fin. The nodal temperatures and their corresponding positions are shown in Fig. 4. What is the temperature of the fin at (a) X-4cm ( and (b) X 8cm

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.3P: 1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of...

See similar textbooks

Similar questions

Question: USE CRANCK NICKLISON METHOD TO Find the steady state temperature distribution at all points of a heated steel plate .The plate has 30 cm width and 30 cm in length . The edges of the sheet are kept at constant temperature: 100 , 80 , 60 ,40 degrees. Assume the sheet is divided into 3x3 grids.
(3) The thermal conductivity of helium at 400 K is 0.176 W m-! K-1. Knowing only this datum, estimate the thermal conductivity of helium at 800 K. Compare your estimate to the value obtained from the figure below. 06 as 02 01 co CO.N A HCI Cl, 200 400 00 Temperature, K 1200 1400 600 What do you conclude about the equation that you used for your estimate?
(a) The coefficient of thermal conductivity of zinc is two times that of copper and the length of copper rod is two times of the Zinc rod, then find the junction temperature. 20°C Zinc Copper O°C (b) How does the coefficient of thermal conductivity changes if (i) Temperature increases (ii) area of the material increases.
2 of 4 I Review I Constants I Periodic Table In this problem you will estimate the heat lost by a typical house, assuming that the temperature inside is Tin = 20°C and the temperature outside is Tout = 0°C. The walls and uppermost ceiling of a typical house are supported by 2 × 6-inch wooden beams (kwood = 0.12 W/(mK)) with fiberglass insulation (kins = 0.04 W/(mK)) in between. The true depth of the beams is actually 5.625 inches, but we will take the thickness of the walls and ceiling to be Lwall = 18 cm to allow for the interior and exterior covering. Assume that the house is a cube of length L= 9.0 m on a side. Assume that the roof has very high conductivity, so that the air in the attic is at the same temperature Part A How much heat per second H (= Q/AT) is lost from the house due to heat conduction? Give your answer in watts, rounding to the nearest 10 W. » View Available Hint(s) Πν ΑΣφ as the outside air. Ignore heat loss through the ground. The effective thermal conductivity of…
NUMBER 2 A piece of beef steak 10 cm thick will be frozen in the freezer room -35 ° C. This product has a moisture content of 73%, a density of 970 kg / m³, and a thermal conductivity (frozen) of 1.1 W / (m K). Estimate the freezing time. using the Plank equation. This product has an initial freezing temperature of -1.75 ° C, and the movement of air in the freezing room gives a convective heat transfer coefficient of 15 W / (m² K). t f = hour.
4 ) Every temperature measuring instrument makes use of specific physical property in order to measure temperature objectively . Which physical properties are used in thermocouple , PT sensors and mercury - in - glass thermometer ? Briefly describe each of this methods.
Please provide accurate answer with proper steps The wall of the furnace is 30.48 mm thick and is insulated from outside. Thermal conductivity of the wall material is 0.1 W/m K and the insulation material is 0.01 W/m K. The furnace operates at 650 0C and the ambient temperature is 30 0 Allowable temperature on the outer side of the insulation is 1000C. Determine the overall heat transfer by conduction per unit area occurring across a furnace wall made from clay. If the air side heat transfer coefficient is 0.4 W/m2 K, calculate the minimum insulation thickness requirement.
A square piece is initially at 10 degrees Celsius everywhere. Each side is 0.05 m long. Then the four sides are instantly heated up to 25 degrees Celsius, 50 degrees Celsius, 30 degrees Celsius, and 0 degrees Celsius. a. Find how long it takes for the temperature profile of this square to become steady if the material is copper. What is the final temperature at the center of the square? b. Find how long it takes for the temperature profile of this square to become steady if the material is air. What is the final temperature at the center of the square? c. Which material takes longer to reach steady state and why?
2. The drawing shows two thin rods, one made from aluminum Midpoint [a = 23 x 10-6 (C°)-'] and the other from steel [a = 12 × 10-“ (C°)-']. Each rod has the same length and the same initial temperature and is attached at one end to an immovable wall, as shown. The temperatures of the rods are increased, both by the same amount, until the gap be- tween the rods is closed. Where do the rods meet when the gap is closed? (a) The rods meet exactly at the midpoint. (b) The rods meet to the right of the midpoint. (c) The rods meet to the left of the midpoint. Aluminum Steel
A wall of a house is made from two layers of bricks enclosing a layer of insulation. A radiator is positioned to cover the whole internal surface, and used intermittently when the internal temperature is low. The external surface is exposed to the outside air. Which of the following assumptions could be used to identify the relevant reduced form of the conduction equation to find the temperature in the wall. a. Conduction is mainly in two directions. b. Conduction is mainly in one direction. c. The wall properties are homogeneous. d. Steady conditions exist. e. Unsteady conditions exist. f. There is an internal volumetric heat generation in the wall.
You have smooth slabs of Titanium (Ti), polycrystalline silica (SiO2), and atactic PS. Rank them from highest to lowest: Thermal conductivity (k) Heat capacity (Cp) Energy band gap (Eg) Thermal expansion coefficient (a) Transparency Resistivity
A plane wall is insulated on its left side (? = 0). The wall generates energy uniformly at arate of ?̇ [W m 3⁄ ] and has thermal conductivity ?. On its right side (? = ?), the wall is exposedto a fluid at temperature ?" with convection coefficient ℎ.a) Draw a schematic of this plane wall. Make the schematic large enough that you cansketch the temperature profile within the wall after solving for it in later steps.b) Write out the full form of the Heat Diffusion Equation (HDE) in the appropriatecoordinate system for this physical scenario. Simplify the HDE and write out theappropriate boundary conditions in their general form (e.g., ?| #$% = ?& ).c) Derive an expression for the steady-state temperature distribution ?(?) within thewall. You may start from the general solution provided in Appendix C of the Bergmantextbook; or you may derive the solution directly from the differential equation andthe boundary conditions. Annotate your schematic by sketching the temperatureprofile…