Water vapor enters a compressor at P₁ = 10 kPa and T₁ = 150°C and leaves at 300 kPa with the same specific entropy as at the inlet. What are the temperature and the specific enthalpy of water at the compressor exit? Use steam tables. 300 kPa Steam compressor ↑ P₁ T₁ out The temperature of water at the compressor exit is The specific enthalpy of water at the compressor exit is T°C. |× 103 kJ/kg.

Water vapor enters a compressor at P₁ = 10 kPa and T₁ = 150°C and leaves at 300 kPa with the same specific entropy as at the inlet. What are the temperature and the specific enthalpy of water at the compressor exit? Use steam tables. 300 kPa Steam compressor ↑ P₁ T₁ out The temperature of water at the compressor exit is The specific enthalpy of water at the compressor exit is T°C. |× 103 kJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water vapor enters a compressor at P₁ = 10 kPa and T₁ = 150°C and leaves at 300 kPa with the same specific entropy as at the inlet. What are the temperature and the specific enthalpy of water at the compressor exit? Use steam tables. 300 kPa Steam compressor ↑ P₁ Ti Wou out The temperature of water at the compressor exit is The specific enthalpy of water at the compressor exit is °C. X 103 kJ/kg.
Oxygen gas is compressed in a piston-cylinder device from an initial state of 0.8 m3/kg and 20 degress C to a fnal state of 0.1m3/kg and 300 degress C. Determine the entropy change of the oxygen during the process. Assume constant specific heats.
Determine change in specific entropy of the ideal gas from state 1 to state 2 in kJ/kg K
PROBLEM 3 Water at the initial pressure and temperature of P₁ = 40 bar and T₁ = 553.15K, respectively, is cooled at constant volume, while heat is transferred to the surroundings at To = 288.15K. At the end of the cooling process, the pressure is P2 = 9 bar. (a) Calculate the entropy change of the water during the process. (b) Calculate the entropy produced during the process.
Water at the initial pressure and temperature of P1 = 40 bar and T1 = 553.15K, respectively, is cooled at constant volume, while heat is transferred to the surroundings at T0= 288.15K. At the end of the cooling process, the pressure is P2 = 9 bar. Questions: (a) Calculate the entropy change of the water during the process. (b) Calculate the entropy produced during the process.
2. Three test tubes containing water. The first test tube containing 10 gm water at 25 °C, second test tube contains 20 gm of water at 50 °C and the third test tube contains 30 gm of water at 80 °C. When they come in contact in such a way so that heat is exchanged between the waters in the test tubes, but no heat is exchanged between the test tubes and the atmosphere/environment. Determine the final temperature of the water, entropy change of each of the water in the test tubes and total entropy change. Consider the C, of water 1 cal/gm/°C and the test tube material doesn't have ant heat capacity.
Determinethecapacityoftheheatingcoilwhen1.5m3/sofmoistairis heated from 21C db, 15C wb with a value of 20C. If the coil uses hot water and enters at 85C and exits at 75C. Determine the mass flowrate of the water
Helium (1.9 kg) is being stored in a rigid tank at 21 deg C. The tank is set outside and the temperature increases to 26 deg C. what is the change in entropy? (Report answer to three decimal places)
A rigid storage tank of 1.5 m³ contains 1 kg argon at 30°C. Heat is then transferred to the argon from a furnace operating at 1300°C until the specific entropy of the argon has increased by 0.343 kJ/kg K. Find the total heat transfer and the entropy generated in the process. Assume that for Argon R kJ/kg K. 0.20813 kJ/kg K, Cv = 0.312
What is the change in entropy of a gas if the temperature increases from 100 K to 101 K when heat is added and the volume is kept constant?
Q1// Define the following Dryness fraction, Latent heat of evaporation, Super-heated vapour Q2// Determine the enthalpy, the entropy, internal energy and specific volume of steam Vapor at 1100 kPa and x-10% Q3// Determine the enthalpy of steam for: a- Saturated vapor at 200°C b- Superheated at 1 MPa and 400°C c- Saturated liquid at 375 kPa
Liquid propane at 1.3 MPa, 36°C, and a flow rate of 0.18 kg/s goes through an expansion valve into a flash chamber at 200 kPa. What are the mass flow rates of liquid and vapor propane coming out of the flash chamber?