1. As a junior city engineer of a municipality, you are tasked todesign the specifications of the pump with 3650 cu.m/day. Thewater source in the municipality is from an open reservoir andwill supply to a pressure tank that will distribute to themunicipality.open4l PressurereservoirTank70 m15 mPumpDetermine the following specifications of the pump and pipingsystem (assume fluid stagnation at the pump).Velocity head at pt.1 to 2 if the diameter of the pipe isa.)200 mmb.)Suction pressure of the pump in kPa (Pressure at pt. 2).c.)Velocíty head at pt.3 to 4 if the diameter of the pipe is150 mmd.)Discharge pressure of the pump in kPa (Pressure at pt. 4).Assume atmospheric pressure at the pump.If an air vent is installed at the pipe just right beforethe pressure tank with diameter of 20 mm, what is thevelocity of discharge in m/s?The height of the pressure tank is 12 m, what is theflowrate in cu.m/hr at pt.5 if the diameter of the pipe is150 mm?e.)f.)

Since the question asked by you contains more than three sub-parts, so according to our guidelines,…

water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open reservoir O Pressure Tank 70m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is 200 mm a.) b.) Suction pressure of the pump in kPa (Pressure at pt. 2). Velocity head at pt.3 to 4 if the diameter of the pipe is 150 mm c.)

water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open reservoir O Pressure Tank 70m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is 200 mm a.) b.) Suction pressure of the pump in kPa (Pressure at pt. 2). Velocity head at pt.3 to 4 if the diameter of the pipe is 150 mm c.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Seven hundred gpm of water are being discharged by a centrifugal pump 5 ft. above the pump inlet. The inlet pressure is 4-in Hg above atmospheric and the discharge pressure is 29 psia. Assume the pump input is 8 hp, if the pump has an 8-inch diameter inlet and a 4-inch diameter discharge: 1.How much pressure loss in the pump? a. 28.4 ft-lbf/lb b. 5 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 2. How much is the velocity loss in the pump? a. 28.4 ft-lbf/lb b. 45.3 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 3. If the pump speed is increased from 1600 to 2400 rpm, what will be the new net flow rate in the pump? a. 800 gpm b. 1050 gpm c. 1400 gpm d. 1965 gpm 4. Find the new brake horse power if the pump speed in increased from 1600 to 2400 rpm. a. 64 hp b. 20.25 hp c. 8 hp d. 30.375 hp
Q Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
Calculate the NPSHA in ft for the following configuration of a pumping system. Pv=924.8Kpaa ... Vessel Pressure = 134.6 psia Minimum Operable Liquid Level 15 ft Water, 350F Datum Suction Line Losses = 5 ft (1.52m)
For the single pump-pipe system below, what will be the changes for the operating point if we increase the pipe size but decrease the shaft speed of the pump? EB H₂ O The operating point will remain the same. O The operating point will occur either at a higher discharge or at a lower discharge, depending on the specific influence of each change. O The operating point will occur at a higher discharge. O The operating point will occur at a lower discharge.
2. A rotary pump directly connected to a 5-Hp electric motor operating at full load under following conditions: a. Fluid Handled : 40 0API Oil b. Temperature : 210C c. Specific Gravity: 0.85 d. Volume Flow Rate : 20 lit/sec e. Total Head : 175 kPa Determine : i. Hydraulic Horsepower ii. Mechanical Efficiency
19. A centrifugal pump delivering 0-04 cumec of water to a height of 20 metres through a 10 cm diameter pipe 100 metres long. If the overall efficiency of the pump is 75% find the h.p. required to drive the pump. Take f-0'01. (51-88 hp)
Q1. The pump with 96.52 cm in diameter characteristics shown in figure below is used to pump water to the system. Neglecting local losses, www a) Calculate flow rate and pump power. b) A new pump from the family with 60 cm in diameter is produced. It oparates with the speed of n=1500 rpm and used to pump gasoline (SG=0.86). Estimate discharge, head and power of the new pump. Note Pipe is cast iron with 0.5 m in diamater and 900 m in length. Fluid is water with density 1000 kg/m³. Take f=0.02 in the analysis. www (a) hil n=710 d'dak 72m 120 7.5 ENPY 105 - 105.4 cm çap 4.5 90 96.52 cm çap 75 - 88.9 cm çap 60 48m 45 30 0.25 0.50 0.75 1.00 1.25 1.50 1.75 Debi ms ENPY m 98 %88 1100 kW 900 kW 750kW Yak, m
Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above the river (dimension "a" on the diagram below) and is supplied by a 6.00 inch schedule 40 pipe. The tank is 19.5 m above the pump (dimension "b" on the diagram below) and is supplied by a 4 inch schedule 40 pipe. The water level in the tank is 4.3 m above the inlet (dimension "c" on the diagram below). The pump delivers 0.021 m/s. Losses are estimated to be 1.2 m between the river and the pump, and 4.2 m between the pump and the tank. Discharge line Suction line Pump River a) Calculate the losses in the suction line in kPa, based on the given head loss in m. kPa b) Calculate velocity in the suction line in m/s. m/s c) What is the pressure at the inlet to the pump in kPa? kPa
Please solve it correctly,Urgent. Question: The discharge pressure of a water pump is 9, 000 kPa. The temperature is 150 deg deg C and density is 917 kg/m3. What is the equivalent pump head in meters? A. 11.005 m B. 1,000.5 m C. 1,050.5m D. 1, 100.5 m
What is the performance of pump (in %, whole number) that supplies 80 gpm of water (80°F) with pressure of145 ft head?
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discharge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023. Include the diagram in your solution. a.100 kPa b.150 kPa c.75 kPA d.225 kPa
A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07