Water is flowing through a 25-mm diameter and 10-m long tube. The water enters the tube at 20\deg C with a mass flow rate of 0.2 kg/s. The outlet mean temperature is 60\deg C, and the tube surface temperature is maintained constant. Determine the hydrodynamic and thermal entry.lengths. Is the flow fully developed? What is the convective heat transfer coefficient inside the pipe?

Water is flowing through a 25-mm diameter and 10-m long tube. The water enters the tube at 20\deg C with a mass flow rate of 0.2 kg/s. The outlet mean temperature is 60\deg C, and the tube surface temperature is maintained constant. Determine the hydrodynamic and thermal entry.lengths. Is the flow fully developed? What is the convective heat transfer coefficient inside the pipe?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.12P

See similar textbooks

Similar questions

QS: Water at 15.56°C i to be heated in a 2-mm-ID tube until the exit temperature reaches 26.67+C. The tube wall temperature is maintained at 48.99-C and the inlet flow velocity is 0.3 m/s. Calculate the length of tube required in meters to accomplish this heating. Also calculate the total heating required, expressed in watts. Answers: L=0.13 m
Water flows inside the tube 45mm diameter and 3.5 meters long at a velocity 1m/s. Determine the heat transfer coefficient and the rate of heat transfer if the mean water temperature is 50 degree celsius and the tube wall is 70 degree celsius. kfor water is 0.68W/m degree celsius and the kinematic viscocity is 0.478x10^-6 m2/s and the Pr= 2.98. use the Dittus and Boelter equation to solve for Nu.
Engine oil flows at a rate of 0.95 kg/s through a tube of 119 mm inside diameter and is heated from 293 to 327 K by condensing steam at 373 K. For the described case answer the following:i. Identify the type of flow and explain briefly about the flow with suitable assumptions & sketches.ii. Determine the inside heat transfer coefficient and rate of heat transfer per meter length of pipe for the identified flow pattern.
The fluid flows at a speed of 0.4 m/s through a horizontally placed smooth pipe with a diameter of 20 mm and a length of 24 m and heats an environment at a temperature of 87 oC. Considering that the pipe surface temperature remains constant, inside the pipe; a) In case of water flow,b) In case of engine oil leakage Calculate the heat transfer coefficient and friction factor in the in-pipe flow and compare and interpret the results.
Heated air at 1 atm and 100°F is to be transported in a 900-ft-long circular section plastic duct at a rate of 1.4 lb/s. I want to determine the head loss and pumping power at the three diameter values in the table below. Complete the table to help me choose a wise diameter. Why would a good design not only focus on minimizing the pumping power? Diameter Head loss, hi Pumping power, W Reynolds number, Re n.d. f n.d. (in) ft hp 8 12 16
Engine oil flows at a rate of 0.05 kg/s through a section of a 2.5 cm diameter tube. The oil enters the section at a temperature of 50 C. The tube wall is kept at 20 C, and it can be assumed that the flow through the section is fully developed. The section of the tube is 5 m long. (a) What is the exit temperature of the oil? (b) What is the heat transfer rate from the oil to the tube wall?
determine the length of the tube required for fully develop flow when 9.06 kg of waterper minute is passed through a tube of 2 cm, it is found to be heated from 20 degree celsiusto 60 degree celsius, the heating is achieved by considering steam on the surface of the tube andsubsequently the surface temperature of the tube is maintained at 90 degree celsius.
Determine the expected Fanning friction factor for water at 28 degrees Celsius, flowing through a smooth tube with a ID of 15 mm at a velocity of 0.3 m/s.
A 10mm diameter and 20m long smooth tube is maintained at a constant surface temperature. Water enters the tube at 25 °C with mass flow rate of 0.01 kg/s. Properties of water at average mean temperature are: K= 0.65W/m.K, dynamic viscosity = 0.486X10^-3 Kg/m.s, Pr = 3.12 The flow at the end of the pipe is ?
Air at 1 atmosphere and a temperature of 60f enters 1/2-in. id tube with a velocity of 80 fps. The wall is maintained at a constant temperature of 210 by condensing steam. Fin the convective heat-transfer coefficient for this situation if the tube is 5ft long
1. A hollow tube is designed to be a heater with the ability to provide uniform surface heat flux of 2000 W/m2 to the water that flows in it. The water with a velocity of0.3 mis enters the tube at a temperature of 15 °C and leaves the tube at a temperature of 45 °C. The tube is 13 m long with a diameter of 5 mm. a. is the flow laminar or turbulent? b. Is the flow fully developed? Prove it with appropriate calculation. c. Calculate the heat transfer coefficient for water that flows inside the pipe. d. What is the temperature of the surface at the exit point of the tube?, e. Evaluate the heat transfer performance when the velocity of water increases to 3 m/s. Briefly discuss your answer. 2. The double pipe, parallel flow heat exchanger is to be used to cool oil using sea water. The oil enter the heat exchanger at 0.15 kg/s and at a temperature of 90 °C. Meanwhile, the sea water enters the heat exchanger at 0.3 kg/sand at a temperature of 10 °C. The area of the heat exchanger is 11. 5 m2…
air at constant pressure of 101.3kpa and 289 k enters inside a tube having an inside diameter of 19.1 mm and a lenght of 2.12m with a velocuity of 24.4m/s. condensing steam on the outside of the tube maintanis the insde wall temprature at 373.1 k knowing that the air flow is turbulent calculate the convection coefficient of the air . ( hint use the simplifiled equaation for air at 1 atm)