Water is flowing through a pipeline shown on the right. The radii of the pipe at points 1 and 2 are 0. 500 [m] and 1.50 [m], respectively. The volume flow rate through the pipeline is 2.50 [L/s]. If the pressure at point 1 in the pipe is 200 [kPa], what is the pressure at point 2, located 5. 00 [m] above point 1? 2 5.00 [m] 1

Water is flowing through a pipeline shown on the right. The radii of the pipe at points 1 and 2 are 0. 500 [m] and 1.50 [m], respectively. The volume flow rate through the pipeline is 2.50 [L/s]. If the pressure at point 1 in the pipe is 200 [kPa], what is the pressure at point 2, located 5. 00 [m] above point 1? 2 5.00 [m] 1

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter15: Fluids

Section: Chapter Questions

Problem 54PQ: Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius...

See similar textbooks

Similar questions

Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
An ideal fluid flows through a horizontal pipe whose diameter varies along its length. Measurements would indicate that the sum of the kinetic energy per unit volume and pressure at different sections of the pipe would (a) decrease as the pipe diameter increases, (b) increase as the pipe diameter increases, (c) increase as the pipe diameter decreases, (d) decrease as the pipe diameter decreases, or (e) remain the same as the pipe diameter changes.
How tall must be to measure blood pressure as high as 300 mm Hg?
A tank with a flat bottom of area A and vertical sides is filled to a depth h with water. The pressure is P0 at the top surface. (a) What is the absolute pressure at the bottom of the tank? (b) Suppose an object of mass M and density less than the density of water is placed into the tank and floats. No water overflows. What is the resulting increase in pressure at the bottom of the tank?
Review. The tank in Figure P15.13 is filled with water of depth d = 2.00 m. At the bottom of one sidewall is a rectangular hatch of height h = 1.00 m and width w = 2.00 m that is hinged at the top of the hatch. (a) Determine the magnitude of the force the water exerts on the hatch. (b) Find the magnitude of the torque exerted by the water about the hinges.
The left ventricle of a resting adult's heart pumps blood at a flow rate of 83.0 cm3/s , increasing its pressure by 110 mm Hg, its speed from zero to 30.0 cm/s, and its height by 5.00 cm. (All cumbers are averaged over the entire heartbeat) Calculate the total power output of left ventricle. Note that most of the power is used to increase blood pressure.
How tall must a water-filled manometer be to measure blood pressures as high as 300 mm Hg?
Water flows through a pipe that gradually descends from a height of 6.78 m to the ground. Near the top, the cross-sectional area is 0.400 m2, and the pipe gradually widens so that its area near the ground is 0.800 m2. Water leaves the pipe at a speed of 16.8 m/s. What is the difference in the water pressure between the top and bottom of the pipe?
Water is moving at a velocity of 2.00 m/s through a hose with an internal diameter of 1.60 cm. (a) What is the flow rate in liters per second? (b) The fluid velocity in this hose's nozzle is 15.0 m/s. What is the nozzle's inside diameter?
(a) What is the fluid speed in a fire hose with a 9.00-cm diameter carrying 80.0 L of water per second? (b) What is the flow rate in cubic meters per second? (c) Would your answers be different if salt water replaced the fresh water in the fire hose?
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
A negative pressure of 25.0 atm can sometimes be achieved with the device in Figure 11.44 before the water separates. (a) To what height could such a negative gauge pressure raise water? (b) How much would a steel wire of the same diameter and length as this capillary stretch if suspended from above? Figure 11.44 (a) When the piston is raised, it stretches the liquid slightly, putting it under tension and creating a negative absolute pressure P=F/A (b) The liquid eventually separates, giving an experimental limit to negative pressure in this liquid.