Water flows through the vertical elbow in Figure 2 and exits to atmosphere.The pipe diameter d, = 10 cm while d, = 3 cm. At flow rate of 0.0153 m3/sthe pressure at section 1 is 2.33 bar. If the weight of water and elbow is 30kg, determine the magnitude and direction of force to hold the pipe in place.y40°2

Answered: Image /qna-images/answer/f8298881-b64f-4210-978e-b1b15a438a2f.jpg

Water flows through the vertical elbow in Figure 2 and exits to atmosphere. The pipe diameter d, = the pressure at section 1 is 2.33 bar. If the weight of water and elbow is 30 kg, determine the magnitude and direction of force to hold the pipe in place. 10 cm while d, = 3 cm. At flow rate of 0.0153 m3/s %3D %3D 1

Water flows through the vertical elbow in Figure 2 and exits to atmosphere. The pipe diameter d, = the pressure at section 1 is 2.33 bar. If the weight of water and elbow is 30 kg, determine the magnitude and direction of force to hold the pipe in place. 10 cm while d, = 3 cm. At flow rate of 0.0153 m3/s %3D %3D 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

= constant Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. Z شكر الكائر 2B ADA=400 mm PA 29.43 N/cm #28 m ZA 28 Dg= 400 mm Pe = 22.563 N/cm ZB = 30 m DATUM LINE
A liquid (SG = 0.562) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -9 psi and 41 psi, respectively. The rate of flow in the pipe is 0.898 ft3/s. What will be the rating of the pump (in horsepower) if its efficiency is 90%? Neglect energy (friction) losses in the system. Use x = 5 ft., y = 9 ft. Use 1 hp = 550 lb-ft/s. Round off to two decimal places.
Water flows steadily through a pipe with ID 35 mm. This pipe expands suddenly to an inner diameter of 75 mm and then stays at that diameter. The flow speed in the 35 mm pipe is 32 m/s. The water gage pressure in the thinner pipe is 510 kPa. 1. What is the pressure at the entrance to the thicker section of the pipe? Is the pressure there larger or smaller than in the thin pipe section? 2. What force is acting on the coupling? Is it tension or compression?
= 4.33 9.74m/ seć n/ 4(0.2)2 HOMEWORK Q1l A (30 N/s) flow throw the reducer of the proceeding problem ,the air in the (300mm) pipe having weight density of (9.8 N/m' ) in the flowing through the reducer producing a redaction of density .assuming that the weight density of the air in the (200 mm) pipe is (7.85 N/ m'). Calèulate the mass and volume flow rate. Q2/ (2) Water enters a conical diffusing passage (see Figure below). With a flow rate of 10ft'/s, and if the entrance cross-section area is 2 ft, what's the average velocity at the entrance to the diffuser? What must the diffuser exit area be to reduce the velocity to 0.5 ft/s? 4 = 2 f Q = 10 cfs - m = AQ: oiclooleo or boon ow.matve binl to sinsb omit letot odi stum hn th .C
Water flows steadily through a horizontal 30 degree pipe bend. At the inlet point 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gauge. At the outlet point 2, the diameter is 0.38 m and the pressure is 145 kPa gauge. Determine the forces F_x and F_y necessary to hold the pipe stationary.
Q 3: The pipe bend shown in figure (3) is in horizontal plane. Oil with sp.gr-0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Determine the force required to hold the bend, (R=1.75 KN) A DA=150mm DB = 100mm B र३० Q3
1. A pipe 100 mm bore diameter carries oil of density 900 kg/m³ at a rate of 4 kg/s. The pipe reduces to 60 mm bore diameter and rises 120 m in altitude. The pressure at this point is atmospheric (zero gauge). Assuming no frictional losses, determine: i. The volume/s (4.44 dm³/s) 11. The velocity at each section (0.566 m/s and 1.57 m/s) 1. The pressure at the lower end (1.06 MPa) 2. A pipe 120 mm bore diameter carries water with a head of 3 m. The pipe descends 12 m in altitude and reduces to 80 mm bore diameter. The pressure head at this point is 13 m. The density is 1000 kg/m³. Assuming no losses, determine i. The velocity in the small pipe (7 m/s) ii. The volume flow rate. (35 dm³/s) 3. A horizontal nozzle reduces from 100 mm bore diameter at inlet to 50 mm at exit. It carries liquid of density 1000 kg/m³ at a rate of 0.05 m³/s. The pressure at the wide end is 500 kPa (gauge). Calculate the pressure at the narrow end neglecting friction (196 kPa) 4. A pipe carries oil of density 800…
1. A pipe 100 mm bore diameter carries oil of density 900 kg/m3 at a rate of 4 kg/s. The pipe reduces to 60 mm bore diameter and rises 120 m in altitude. The pressure at this point is atmospheric (zero gauge). Assuming no frictional losses, determine: i. The volume/s (4.44 dm³/s) ii. The velocity at each section (0.566 m/s and 1.57 m/s) iii. The pressure at the lower end. (1.06 MPa)
6.5 BELLOWS 6100mm The horizontal elbow is joined by bellows to the rest of the piping system and it transports water. Determine the X and Y components of the force needed to keep the elbov in posi- tion. The pressure at A and B is 200 kPa, the flow rate is 30 L/s and the pipe diameter is 100 mm. 6.6 Water flows at a rate of 0,055 m³/s through a piping system and then issues from the pipe of 50 mm diameter into the atmosphere. Ø150mm Ø50mm Ignore losses in the pipe and determine the force required at the flange to keep the nozzle in position. (Hint: first determine the pressure at A with Bernoulli's equation.)
1. For the pipe and nozzle system shown on the first figure, the velocity of the free water jet is 6 m/s, calculate the flow rate Q and the velocity in the main pipe. If the manometer fluid is mercury (density = 13500 kg/m³), determine the manometer reading H. 30 dia. -100 mm dia Mercury ל >
Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the pipe forms with the vertical direction is a. Assume that when the fluid enters the pipe its velocity is uniform (i.e., it has the same value over the entire cross-section of the pipe) and equal to U in the axial direction. In the radial and angular directions, the velocity is zero. So, it is: 2 =0: v(r, 0, 2) = Ue, (1.1) Here v is the fluid velocity and e, is a vector of unit magnitude parallel to the coordinate axis z; furthermore, we have assumed that the pipe inlet is located at z = 0. Near the entrance of the pipe, the velocity profile varies in the axial direction. But after a certain entrance length, the profile becomes fully developed, no longer changing with z. The evolution of the velocity profile is sketched in Fig. 1, where, for clarity, the pipe inclination is not shown. The entrance length is denoted by L.. For z > L., the fluid velocity is no longer a function of the axial…
4. A pipe carries oil of density 800 kg/m³. At a given point (1) the pipe has a bore area of 0.005 m² and the oil flows with a mean velocity of 4 m/s with a gauge pressure of 800 kPa. Point (2) is further along the pipe and there the bore area is 0.002 m² and the level is 50 m above point (1). Calculate the pressure at this point (2). Neglect friction. (374 kPa)