VOUT-V, (R,/R₂) FlexiForce V, -Sv POWER GND GND MCP 6001 货 Determine Rf in the circuit in order to obtain 0.5 V to 5 V output in response to a force of 0 kg to 3.0 kg when using a FlexiforceTM SSB-T sensor that has 400 kOhm when unloaded and 40 kOhm when applying 3.5 kg. Give your answer in KOhm, no units. VouT SV*

VOUT-V, (R,/R₂) FlexiForce V, -Sv POWER GND GND MCP 6001 货 Determine Rf in the circuit in order to obtain 0.5 V to 5 V output in response to a force of 0 kg to 3.0 kg when using a FlexiforceTM SSB-T sensor that has 400 kOhm when unloaded and 40 kOhm when applying 3.5 kg. Give your answer in KOhm, no units. VouT SV*

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

uo A:EV * ll. pluli ► b89f3244-f736-4021-901... PI EXPlain The effect of increasing The filter Capacitance on The outfut Voltage in The haif - wave rectifier and filber Circuit ? CS Scanned with CamScanner
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. the direction of conventional current flow O c. that it is a P-channel MOSFET O d. the direction of electrons
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
3. Graphical Representation of the signal 1) Write the type of the voltage from simulation results: 2) Write the value of the voltage from simulation result: L....... -2 DDU 12ns SónG Trace Color Trace Name X Values CURSOR 1,2 V(R1:1,0) Y1 Y2 Y1 - Y2 5.0373m 0.000 5.0373m 249.983 0.000 249.983 Y1(Cursor1) - Y2(Cursor2) Y1-Y1(Cursor1) Y2 - Y2(Cursor2) Max Y Min Y Avg Y 249.983 0.000 0.000 249.983 0.000 124.991
LTE .!!: 0:00 docs.google.com a What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave rectifier read (2.36 v), and true form factor of input waveform is (1.414). 3 volt 1.5 volt 1 volt 2.36 volt If the value of waveform does not remain constant with time, the signal is referred to as direct (d.c) signal * True False •.. 6 +
3. Determine Veand Sketch output waveform for the clamper network shown. 20 V Si C Vi R 4 V- | -20 V 4. An RC filter stage (R = 42 0, C = 220 µF) is used to filter a signal of 30 V dc with 6 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 200-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
Shown below is a section from the datasheet of 74LS32, a quad 2-input OR chip. What is the noise margin high (in V) of this chip? Limits Symbol Parameter Min Typ Max Unit VIH Input HIGH Voltage 2.0 V VIL Input LOW Voltage V 0.8 VIK Input Clamp Diode Voltage -0.65 -1.5 V V VOH Output HIGH Voltage 3.5 V V VOL Output LOW Voltage 0.35 0.5 V 20 μA IH Input HIGH Current 0.1 mA IIL Input LOW Current -0.4 mA los Short Circuit Current (Note 1) -100 mA Power Supply Current Icc 6.2 Total, Output HIGH mA Total, Output LOW 9.8 74 74 74 2.7 -20
M1 and M2 are matched, what is the output common mode voltage? Draw the output wave form if Vi is a sine wave of 10MHz and peak amplitude of Vdd/4, assume high gm, long channel, find the output signal shape, frequency and peak to peak amplitude, Rin ww RF VDD M2 M1 Rout
Subject:Electronics Engineering How JFET has been constructed? Explain the principle of operation of JFET at different values of VGS and VDS
The Pinch off voltage for N-Channel JFET is -3V, maximum saturated drain current 8mA and the value of VGS is -1.5 V. Calculate drain current, a. 4 mA b. 2.5 mA c. 2 mA d. 18 mA
Why was the smoothing capacitor C1/47 not placed directly after the unit bridge? It was placed in its place in the circuit, where its work as a smoothing filter for the base voltage of transistor Q1 was deliberately stopped, but it works with the rest of the circuit elements. Capacitor C1 is isolated between transistor Q1 and the rest of the circuit by a diode (1N4001).