vą(n) = Q[v(n)] ) with a midtreat quantizer. The range of the signal is ±5 V and the word ength of the quantizer 4 bits. The quantizer is at digital full scale. a) How many quantization levels L does the quantizer have? What is the value of A? b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. :) For time index n = 1250 calculate the quantized value va (n), the quantization error eq(n) and represent vą (n) using RZ code. d) Calculate the power P of the quantization noise. e) Determine the SNR in dB.

vą(n) = Q[v(n)] ) with a midtreat quantizer. The range of the signal is ±5 V and the word ength of the quantizer 4 bits. The quantizer is at digital full scale. a) How many quantization levels L does the quantizer have? What is the value of A? b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. :) For time index n = 1250 calculate the quantized value va (n), the quantization error eq(n) and represent vą (n) using RZ code. d) Calculate the power P of the quantization noise. e) Determine the SNR in dB.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

az/a.Design Circint as the following pescripton: A. the positive Cyycle of the vout signal is 3-2 and Negadive cycle is 4-3 (Note: we must used preetical Diodes and vin is tov)
What is the advantage of using square wave-form as an Input Signal? What is the shape ofthe output when the input signals are sinusoidal and triangular in shape? ( Use Functiongenerator and Oscilloscope to observe the output)
Signal and system problem plz explain every step how do this step
pls describe this circuit and relationships of waveforms, outputs inputs etc
Project Title: Design a circuit which will give a fluctuating DC Output voltage for an Input Square Wave. Specifications: You will have a square wave as your source voltage where the square wave will have a Peak Amplitude of 24 V and Minimum Amplitude as 0 V with a frequency of 100 Hz. The output voltage is across a capacitor which will fluctuate. Besides, the driving voltage of the capacitor should be another square wave having a Peak Amplitude of 10 V and Minimum Amplitude as 0 V with the same frequency. The time constant is Ims. Now, design the whole circuit. Show the input/output graph in PSpice for the first 10 cycles. Submission Guidelines: One group should submit one simulation (.sch) file and one report (.pdf) file. The report must contain the following: 1. Cover Page 2. Objective (write the problem statement here) 3. Design (detailed calculation of values for all the selected components) (explain how you are getting the driving voltage of the capacitor from the source voltage.…
1 In a certain digital waveform, the period is two times the pulse width. The duty cycle is 50% The given hexadecimal number 2B.3116 is equivalent to 53.1428 An octal equivalent for fraction decimal number is obtained using repeated division-by-8. 2.
For the signal flow graph of the ints given figure consider the following statements: 1. It has three forward paths. 2. It has three individual loops. 3.lt has two non touching loops. out of above the correct statements are X2 X3 О 2,3 O 1,2 O 1, 2, 3 О 1,3
Complete SolutionDraw the waveform of the given clipper circuit and determine the following: a.) At 0V, what is the output voltage?b.) At +20V, what is the output voltage?c.) At -5V, what is the output voltage?
D1 D V1 D4 D2 V D D Diode Model: 1N5817 R = 10k Vi= sine (0 5 100) Given the parameters above, simulate the given circuit using .tran 0 30m 0. Solve for the output peak to peak voltage across the resistor and the output frequency measured across the resistor. Output Frequency = (When computing for the frequency, use 4v as reference point) Output Voltage (pk-pk) = + R1 R D3 D
select one quickly Mod-N counters can be used for frequency ........... . a) dividing, b) subtracting , c) adding , d) multiplying.
2. For the below figure - a) Derive the output and minimize the output function using Karnaugh map b) Draw the wave form of output if B
(3) A sinusoidal signal of frequency 200 Hz is sampled at a rate of 1200 samples per second. Draw two cycles of the analog signal and show where sampling occurs on the waveform.