Using only 2-input totem-pole gates and as few inverters as possible, complete the logic to allow the right two systems to go ahead if any of the left two systems are ready and the boiler is not hot. There is an overall active low enable EN. Only if the overall enable is active, the two right systems are permitted to go ahead if the other three signals want them to go ahead. Left 1 Left_2 R1 R2 temperature sensor H EN GO WAIT Right1 Right2

Using only 2-input totem-pole gates and as few inverters as possible, complete the logic to allow the right two systems to go ahead if any of the left two systems are ready and the boiler is not hot. There is an overall active low enable EN. Only if the overall enable is active, the two right systems are permitted to go ahead if the other three signals want them to go ahead. Left 1 Left_2 R1 R2 temperature sensor H EN GO WAIT Right1 Right2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 1) If six NOT (inverters) gates are connected in series and the input to the first gate is a LOW (0) the output of the FIFTH. gate will be:
(b) For a gated S-R latch. determine the Q output for the inputs in the following Figure. Show it in proper relation to the enable input, also draw the input waveforms on your answer script. Assume that Q starts LOW. EN S R Minimize the combinational logic circuit in the following figure using Karnaugh's map only. Inverters for the complemented variables are not shown. Q2.
d) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.
Q2/A) Design 8x1 multiplexer using 2x1 multiplexer? Q2 B)Simplify the Logic circuit shown below using K-map then draw the Simplified circuit? Q2/C) design logic block diagram for adding 12 to 5 using full adder showing the input for each adder?
Consider a family of logic gates that operate under the static discipline with the following voltage thresholds: VI=1.5V, VOL=0.5V, VIH=3.5V, and VOH=4.4V. a. What is the lowest voltage that can be output by an inverter for a logical 1 output? b. What is the highest voltage that must be interpreted by a receiver as logical 0? c. What is the lowest voltage that must be interpreted by a receiver as logical 1?
Consider a family of logic gates that operate under the static discipline with the following voltage thresholds: VI=1.5V, VOL=0.5V, VIH=3.5V, and VOH=4.4V. a. What is the lowest voltage that can be output by an inverter for a logical 1 output? Explain. b. What is the highest voltage that must be interpreted by a receiver as logical 0? Explain. c. What is the lowest voltage that must be interpreted by a receiver as logical 1? Explain.
Five inverters are connected in series. Which of the following statements is correct? The output is high if the input is high. • The output is low if the input is low. The output is high if the input is low. The output is low if the input is high.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Implement the function, W using ONE 4-to-1 multiplexer and other logic gates. b) Implement the function, X using ONE 4-to-1 multiplexer and other logic gates. Implement the function, Y using TWO 4-to-1 multiplexer and other logic gates. d) Implement the function, Z using ONE 8-to-1 multiplexer and other logic gates. Table Q1 ВCD Braille A B D W Y 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 A ololO
A d. B Figure 1 3. Referring to the logic circuit in Figure 1, determine: a. The simplified Boolean expression. b. The output waveform. C H c. Due to fabrication errors, lines d and f were shorted to the supply voltage. What happens to the output of the circuit? d. Your hardware resources are limited to 2-input NOR gate only. Draw the gate schematic of the simplified Boolean expression in 3(a).
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
The no. of turns in secondary winding is more than that of primary winding. The output voltage is higher than input voltage. Significantly used in inverters. Indentify what is asked