Use dynamic programming method to determine the most economical units to be committed to supply a load of 350MW. Load is varying in step size of 50MW. There are two units with the following data- C1=0.004 P1 P1+ 6.2 P1+ 320 RO/hr C2=0.008P2 P2 + 6.9 P2 + 200 RO/hr Where P1 and P2 are in MW. Plant outputs are subject to the following limits(in MW). Lower limit: 50 for both the generators. Upper limit: 300 for both the generators. Paragraph BI E BD

Use dynamic programming method to determine the most economical units to be committed to supply a load of 350MW. Load is varying in step size of 50MW. There are two units with the following data- C1=0.004 P1 P1+ 6.2 P1+ 320 RO/hr C2=0.008P2 P2 + 6.9 P2 + 200 RO/hr Where P1 and P2 are in MW. Plant outputs are subject to the following limits(in MW). Lower limit: 50 for both the generators. Upper limit: 300 for both the generators. Paragraph BI E BD

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

The electrical equivalent of mechanical load in induction machine is? a. r2/s b. r2*(1-s)/s c. r2/(1-s) d. r2
Subject Linear Control I need answer for MCQ
Explain why this is the equation for nodal analysis. I need to know how it became negative and positive. Why did Vs1 and Vs2 became negative? Why did Vs3 became positive and so on?
Load cells are used for the measurement of:Select one:a. Velocity O b. StrainO c. WeightO d. Stress
b) Use the ALU 74181 in the figure below and the tables (one is enough; second maybe, need to check the new kit) to implement : A + B, A – B, A. B. (MSB) (LSB) 10 (MSB) F3 F2 F1 FO S3 Cn+4 16 s2 20 U14 15 S1 14 so A3 A2 A1 AO B3 B2 B1 B0 M Cn 24 23 22 21 28 27 T26 25 (LSB) (MSB) (LSB)(MSB) (LSB) And given that under M = 1 the circuit performs the following arithmetic and logic functions according to Table 11.1. Input selection S3 Output M-H S2 SI Cn=L. F3 F2 F1 FO A 1 -A В -B A&B AxB 1 A'B 1 Ax(-B) (-A)xB (-A)x(-B) 1 1 ACTIVE HIGH DATA M-L: ARITHMETIC OPERATIONS SELECTION M-H LOGIC s3 s2 s1 so Ino carry) (with carry) F-A PLUS 1 F- LA + B) PLUS 1 F- (A + BI PLUS 1 FUNCTIONS L L F-A F-A+B F-AB F-A H FA+B F-A+T F- MINUS 1 12s COMPL) F-A PLUS AB F- IA + BI PLUS AB L L L L F-0 F-ZERO F- AB F-A PLUS AB PLUS 1 F- (A + BI PLUS AB PLUS 1 L L L H L F-AOB F- AB L L F-A MINUS B MINUS 1 F-A MINUS B F- AB MINUS 1 F- A F-A PLUS AB PLUS1 F-A PLUS B PLUS 1 F- IA + B PLUS AB PLUS 1 L H L F-A PLUS AB…
Solve Figure 2, 3, and 4. Please do it step by step without jumping any mathematical steps -for example, if you have to factor out dont just write the result of the factorization, but show the process-. And explain what is heppening in relevant steps. Thank you.
Can someone pls help me with problem 2.6 with detail explanation on convolution because i still don't understand this. Needs Complete solution with 100 % accuracy.
Find the current l4 for the figure shown below. 100A 40A 12 I1 80A 13 15 10A 14? a. 100A O b. 400A c. 200A O d. 150A
Two gen. A and B operate in parallel. The station capacity of A is 50MW and that of B is 25MW. The full load speed regulation of station A is 3% and of B is 3.5%. Find the load sharing of 50MW between both the machine and the no load frequency is 50Hz. Don't use pen and copy.
List 3 different concepts of Electricity(gravity) not hydro generation using weights design. Each concept must have an introduction and design description. Include a photo of each trenching machine design and modeling concept. For Example : Mass electricity generation
You have developed an idea for using a poly Si surface‐ micromachined cantilever. Initially, you designed a process flow for creating this simple structure, and the process flow is detailed in the figure below. ( cross section view and top view)There are several critical errors with this process (things that won’t work or won’t produce the result). Please find the critical errors in this process flow and, where possible, suggest alternate approaches. Do not worry about the accumulation of errors, but rather treat each step assuming that the structure up to that step could be created.This structure is actually quite simple to make. Develop a simpler process flow and associated masks to create the final structure. Be sure to show cross‐sectional and planar views of all key steps in the process.
show complete solution INCLUDE FIGURES