Two steel plate tension members have been connected using 0.72” diameter bolts arranged in an equally-spaced four by four square formation.Total plate self-weight is specified as 912 pounds.Design of the elements adhered to the set of values that are twice as much as the minimum requirements. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 54ksi and the min required edge distance as 0.125ft. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load(excluding the self-weight)and live load assuming live load is half as much as dead load including the self-weight of the plates

Two steel plate tension members have been connected using 0.72” diameter bolts arranged in an equally-spaced four by four square formation.Total plate self-weight is specified as 912 pounds.Design of the elements adhered to the set of values that are twice as much as the minimum requirements. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 54ksi and the min required edge distance as 0.125ft. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load(excluding the self-weight)and live load assuming live load is half as much as dead load including the self-weight of the plates

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.4.5P

See similar textbooks

Similar questions

A L 3 x 2 x ¼ is connected to a gusset plate via six bolts. The nominal diameter of the bolt is 0.25 inches, the pitch spacing is 1.75 inches, the gage spacing is 2 inches, and the thickness of the connection is (¼) inch. The yield stress is 50 Ksi and the ultimate stress is 60 Ksi. Consider section line (a-a') for the analysis. . a. What is the effective net area (Ae) of the angle section in inches2 [a-a']?(The shear lag factor is "0.80") b. What is the design tensile yielding strength in Kips for the steel member? c. What is the design tensile rupture strength in Kips for the steel member? d. What is the minimum Factor of Safety if a tensile load of 23 Kips is applied to the angle section? please make sure the answer is correct 100% I only need the final answers
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt = 20 mm Both the tension member and the gusset plate are of A 36 steel. Fy = 248 MPa, FU = 400 MPa. Shear stress of bolt Fnv = 300MPa. Questions: a.Determine the shear strength of the connection. b.Determine the bearing strength of the connection. c. Determine the block shear strength of the connection.
STRENGTH OF MATERIAL(SIMPLE STRESS) PLEASE INCLUDE FBD 100% GUARANTEE UPVOTE
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 150 mm x 90 mm x 12 mm angular section is welded to a gusset plate as shown. Area of the angle is 2736 sq.mm, allowable shear Fv is 150MPa, Allowable tensile stress Ft = 0.6Fy with Fy = 250 MPa. Questions: a) Design force P b) Total required length of weld using 12 mm fillet weld c) Value of “b”
For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa (shear stress) Tensile stress=0.60 Fy Bearing stress = 1.35 Fy Rivet hole has a diameter 2mm greater than the rivet diameter. The main plate has a width of 300mm and a thickness of 20mm. Determine the diameter of rivets such the shear capacity of the rivets is equal to its bearing capacity. Also, compute the maximum value of P so as not to exceed the allowable tensile stress of plates. P- O JAK O O 300 mm -P/2 -P/2
The vertical member shown in Figure STCN17.02 consist of two angles welded to the 8-mm thick gusset plate. Given the following data: Angle size: 75 mm x 50 mm x 6 mm (long legs back-to-back) Area of one angle = 738 mm Size of weld = 6 mm Yield strength of steel, Fy = 248 MPa Allowable weld shear stress, F, = 124 MPa a = 25 mm a. Determine the safe capacity of the vertical member in kN. b. If P= 185 kN, determine the length of weld L2 (mm) such that each weld have equal shear stress. Neglect end returns. c. If L1 = 140 mm and L2 = 70 mm, determine the safe load P (kN) based on weld capacity assuming all welds have equal stress. AP L1 L2
A steel plate is to be attached to a support with three bolts. The cross-sectional area of the plate is 800 mm² and the yield strength of the steel is 260 MPa. The ultimate shear strength of the bolts is 570 MPa. A factor of safety of 1.67 with respect to yield is required for the plate. A factor of safety of 4.0 with respect to the ultimate shear strength is required for the bolts. Determine the minimum bolt diameter required to develop the full strength of the plate. Note: consider only the gross cross-sectional area of the plate-not the net area. Support Plate ↓ P
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
H.W (2): A 37.5 mm round bar has been machined from AISI 1050 cold-drawn round bar Su =689 MPa. This part is to withstand a fluctuating tensile load varying from 0 to 72.5 kN. Because of the design of the ends and the fillet radius, a fatigue stress-concentration factor of 1.85 exists. Find the factor of safety F.S.
Compute the available block shear strength of the gusset plate and design tension strength. 2 in A- B- D 3 in El F. 2 in 0.375 in 0.375 in 2 in 3 in 3 in 2 in (not to scale) Section properties Material properties plate width = 7 in ASTM A36 steel plates plate thickness =/s in F, = 36 ksi %3D standard hole size F,= 58 ksi
What is the axial stress in the bronze rod (in MPa)? 2m 3m 6o kN mm 15mm banzerod
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten A plate having a width of 400 and a thickness of 20mm is to be connected to two plates with thickness of 12mm by four rivets. The allowable shear stress for the rivets is 150 MPa and for bearing is 1.35 Fy. If the yield strength and the ultimate strength is 248 MPa and 400 MPa respectively. Determine the Following: a.) Required diameter of rivets w/o exceeding the aloowable stress in the shear. b.) Required diameter of rivets w/o exceeding the allowable stress in bearing. c.) Required diameter of rivets w/o exceeding the allowable stress in tension.