Two kilograms of water is contained in a piston-cylinder device where a linear spring is attached to the piston, as shown in the figure. The spring was initially at rest, when the pressure of water inside the cylinder was 100 kPa and the volume was 0.2m³. Heat is then added to the system. As the piston first hits the stops, it is known that the volume was 0.8 m³ and the temperature was 600°C. The heating is continued until the pressure reaches 1.2 MPa. Determine the final temperature, sketch the process on a P-V diagram, and calculate the work done during the entire process. H,0

Two kilograms of water is contained in a piston-cylinder device where a linear spring is attached to the piston, as shown in the figure. The spring was initially at rest, when the pressure of water inside the cylinder was 100 kPa and the volume was 0.2m³. Heat is then added to the system. As the piston first hits the stops, it is known that the volume was 0.8 m³ and the temperature was 600°C. The heating is continued until the pressure reaches 1.2 MPa. Determine the final temperature, sketch the process on a P-V diagram, and calculate the work done during the entire process. H,0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a reciprocating air compressor, high pressure air in the cylinder pushes the piston against the external load and expand to a lower pressure. In a test the following measurements were noted:Internal energy of air before expansion = 27 kJInternal energy of air after expansion = 8 kJHeat entering the cylinder during the process = 2 kJSHOW THE DIAGRAM USING THE GIVEN PROVIDED
A 8 kgs gas contained in a vertical piston cylinder assembly is shown in the figure below. The area and the mass of the piston are 300 cm2 and 15 kg, respectively. A spring is loaded in the piston, which the force exerted varies linearly with the displacement, s. At initial position, the piston face is at s=0, the spring exerts no force. Heat is added to the air causing the gas to expand until the piston reached the stops at s=0.08m and the heat transfer ceases. The atmospheric pressure is 1 bar, the observed gravitational acceleration is g=9.81 m/s2, consider the spring constant, k to be 8,500 N/m and neglect friction between the piston and the cylinder. Determine: a.The initial pressure of the gas in Kpa b.The work done by the gas on the piston in J c.The heat transfer in J, when the specific internal energies of the gas at the initial and final states are energies of the gas at the initial and final states are 210 KJ/Kg and 335 KJ/Kg, respectively
Graw 1 Q A The force generated by a spring is given by F= kx where k is the spring constant, and x is the deflection of the spring. The spring shown in the figure has a spring constant of 9.5 kN/cm. The pressures are P-5000 kPa, P₂=10000 kPa, and P3 = 1000 kPa. If the piston diameters are D=8 cm and D2-3 cm, how far will the spring be deflected? Z Spring- The spring will deflect 1.717 cm. 2 W D₁ S 309 F2 X #3 E D 80 F3 $ 4 C 888 F4 R 25 % V MA FS T U N * 00 8 J DII - M ( 9 K DD F9 O ) V S 0 J L T' P
One closed tough tank inside the package The pressure inside the tank is 800 kPa if the mass of water in liquid form is 0.05 kg and the mass of water in gas form is 1.95 kg. The whole body is vaporized. Find this new pressure.
Skg of Steam at pressure of 4.9 bar is produ- ced from water at 20c. Determine the amount of heat supplied if the Steam is o.9 dy.
Volume 0.05 m3 while the piston is attached with the pinin a cylinder with 200 kPa pressure and 300 Kthe temperature is. As a result of heat transfer from the environment, the pressure is 0.4 MPa, the pin breaks, and when the system becomes thermodynamically balanced, its volume is 0.1 m3. Area of piston 0.05 m2, piston and masses on 150 kg and atmospheric pressure102 is KPA. a)Find the temperature at the moment the pin breaks. b)Calculate the pressure and temperature after the pin breaks and reaches the equilibrium position.
Q3: The cylinder shown in Fig. (2), Ayinder=7.012cm, has two pistons mounted, the upper one, mp1 =100kg, initially resting on the stops. The lower piston (m2 =0kg) has 2kg water below it, with a spring (linear) in vacuum connecting the two pistons. The spring force is zero when the lower piston stands at the bottom, and when the lower piston hits the stops the volume is 0.3m. The water, initially at 50kPa, V =0.00206m', is then heated to saturated vapor. Determine: (1) the initial temperature (2) the pressure that will lift the upper piston (3) The condition of steam when the lower piston hits the stops (4) the work done by the water (at saturated vapor state).
A man is standing on a board on a frozen lake where there is no friction between the board and the ice surface. Tha man's mass is 2 m and the boaf's mass is 4 m. The board has length L. He walks from 1/5 Lfrom the left end of the board to 1/5 L from the right end of the board. How far and in which direction does the board move during this process?
can you aswer part b and please accept the mass on the right (2m) as 2.5kg , the one on the left (m) as 6.25 kg. and the radius as 1.9 m .
COnsider the system
Volume 0.05 m3 while the piston is attached with the pinin a cylinder with 200 kPa pressure and 300 Kthe temperature is. As a result of heat transfer from the environment, the pressure is 0.4 MPa, the pin breaks, and when the system becomes thermodynamically balanced, its volume is 0.1 m3. Area of piston 0.05 m2, piston and masses on 150 kg and atmospheric pressure102 is KPA. Calculate the pressure and temperature after the pin breaks and reaches the equilibrium position.
Patm 1. Initially; the piston sits on the stops and the linear spring exerts no force, the specific volume is 0.05 m /kg and the pressure is 125 kPa. Atmospheric pressure is 100 kPa, mass of the piston is 102 kg, and area of the piston is 200 cm?. The linear spring exerts a force on the piston in such a way that the specific volume becomes 0.08 m'/kg when the pressure reaches 200 kPa. Heat is transferred to the water until its temperature is 115 °C. Calculate work and heat transfer, showing the process on a P-v plot. Hint: In the final stage, the temperature is 115°C, but the pressure is not given. You need to find P and v using the tables and P-v plot.