Try Onescene 13 of 13Bar properties800 mmDetermine the internal forces and normalA1500 mm?stresses in bars (1) and (2). (+ =(2)tension,compression)- =E,80 GPa%D470 mm350 mm?Also, determine the deflection of the rigidbar in the x direction at C. (+= right,= left)A2 =E,80 GPa- =45 kN630 mm(1)F153.289kNX1000 mm470 mmF215.576kNXX106.578MPAX0244.5MPAXTry OneVC3.118mmX1st2nd 3rdEnterattempt

Answered: Image /qna-images/answer/cf35e38f-d2fb-498a-9bb0-f42b6875a2f8.jpg

Try One scene 13 of 13 Bar properties 800 mm Determine the internal forces and normal 500 mm? stresses in bars (1) and (2). (+= tension, – = compression) A1 = (2) E, 80 GPa Also, determine the deflection of the rigid bar in the x direction at C. (+= right, - = left) 470 mm A2 = 350 mm? E, = 80 GPa 45 kN 630 mm B (1) F1 53.289 kNX 1000 mm 470 mm F2 15.576 kNX 106.578 MPAX 02 44.5 MPAX Try one 3.118 mmX 1st 2nd 3rd Enter attempt

Try One scene 13 of 13 Bar properties 800 mm Determine the internal forces and normal 500 mm? stresses in bars (1) and (2). (+= tension, – = compression) A1 = (2) E, 80 GPa Also, determine the deflection of the rigid bar in the x direction at C. (+= right, - = left) 470 mm A2 = 350 mm? E, = 80 GPa 45 kN 630 mm B (1) F1 53.289 kNX 1000 mm 470 mm F2 15.576 kNX 106.578 MPAX 02 44.5 MPAX Try one 3.118 mmX 1st 2nd 3rd Enter attempt

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.25P

See similar textbooks

Similar questions

An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A prismatic bar of length L = 1.8 m and cross-sectional area A = 480 mm" is loaded by forces P{= 30 kN and A = 60 kN (see figure) The bar is constructed of magnesium alloy having a stress-strain curve described by the Ram berg-Osgood equation: 45.000 618 UW id which u has units of mega pascals (MPa). (a) Calculate the displacement 8t- of the end of the bar when the load P:acts alone. (b) Calculate the displacement when the load P, acts alone. (c) Calculate the displacement when both loads act simultaneously.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
A bar of monel metal with a length L = 9 in. and a diameter d = 0225 in. is loaded axially by a tensile force P (see figure). If the bar elongates by 0.0)95 in., what is the decrease in diameter
A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
The strength-to-weight ratio of a structural material is defined as its load-carrying capacity divided by its weight. For materials in tension, use a characteristic tensile stress obtained from a stress-strain curve as a measure of strength. For instance, either the yield stress or the ultimate stress could be used, depending upon the particular application. Thus, the strength-to-weight ratio RS/Wfor a material in tension is defined as Rs/w= in which a is the characteristic stress and 7 is the weight density. Note that the ratio has units of length. Using the ultimate stress Uas the strength parameter, calculate the strength-to-weight ratio (in units of meters) for each of the following materials: aluminum alloy 606I-T6, Douglas fir (in bending}, nylon. structural steel ASTM-A57.2, and a titanium alloy. Obtain the material properties from Tables [-1 and 1-3 of Appendix I. When a range of values is given in a table, use the average value.
Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.
A statically indeterminate stepped shaft ACE is fixed at ends A and B and loaded by a torque TQat point C (see figure). The two segments of the bar are made of the same material, have lengths L4and LB, and have polar moments of inertia IAand Ipb. Determine the angle of rotation 4>of the cross section at Cby using strain energy. Hint: Use Eq, (3-55b) to determine the strain energy Urn terms of the angle d?. Then equate the strain energy to the work done by the torque to. Compare your result with Eq. (3-52) of Example 3-9.
A mountain bike rider going uphill applies a force P = 65 N to each end of the handlebars AB CD, made of aluminum alloy 7075-T6, by pulling on the handlebar extenders (DF on right handlebar segment). Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A), Segments AB and CD are prismatic with lengths Lvand L3 and with outer diameters and thicknesses J01, /01 and d03, /03, respectively, as shown. Segment BC of length L2, however, is tapered, and outer diameter and thickness vary linearly between dimensions at B and C Consider shear, torsion, and bending effects only for segment AD; assume DFis rigid. Find the maximum tensile, compressive, and shear stresses adjacent to support A. Show where each maximum stress value occurs