To transmit 20 kW at 1000 rpm with a service factor of 3, a rigid flange coupling should be designed. Find the size of the shaft, the key and the flange if the shaft and the key are made of steel with allowable shear stress of 100 MPa and allowable crushing stress of 220 MPa and the flange is made of cast iron with allowable shear stress of 12 MPa.

To transmit 20 kW at 1000 rpm with a service factor of 3, a rigid flange coupling should be designed. Find the size of the shaft, the key and the flange if the shaft and the key are made of steel with allowable shear stress of 100 MPa and allowable crushing stress of 220 MPa and the flange is made of cast iron with allowable shear stress of 12 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
A 45 mm diameter shaft is made of steel with a yield strength of 400 MPa. A parallel key of size 14 mm wide and 9 mm thick made of steel with a yield of 340 MPa is to be used. Find the required length of key, if the shaft is loaded to transmit the maximum permissible torque. Use maximum shear stress theory and assume a factor of safety of 2.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
A mild steel shaft has to transmit 75 kW at 200 rpm. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the shaft and keys 40 N/mm²Shear stress for bolts = 28 N/mm²Shear stress for C.I. coupling = 20 N/mm² Take wearing stress as twice the shear stress value and number of bolts for coupling as 6.
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
A keyed gears delivers a torque of 912.4 N-m thru its shaft of 63.5 mm outside diameter. If the key has thickness of 15.875 mm and width of 11.1125 mm, find the length of the key. Assume permissible stress value of 61.2 MPa for shear and tension at 99.8 MPa
A pulley is keyed to a 28 mm steel shaft with a 7 mm x 8 mm x 20 mm key. If the hub length is 20 mm and the allowable crushing stress for the key material is 105 MPa, How much torque can be transmitted in kN-m?
Design a flanged coupling that will be able to carry power of 1,500 HP using a factor of safety of 3.3 at 630 rpm. The shaft diameters of the equipment the coupling will connect are both 5 inches. Check your design for the following stresses if N = 3.3 is satisfied: 1. Bolt shearing; 2. Bolt bearing; 3. Shearing of hub from coupling flange; 4. Shear on key; 5. Compression on key; Select dimensions whichever is higher. 6. Calculate also minimum length of engagement of the bolt and nut if these are of the same material. 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only Instructions:
A 1000 mm cast iron pulley is fastened to a 112 mm shaft by means of a 28 mm squarekey 160 mm long. The key and shaft are SAE 1030 steel annealed with allowableshearing of key at 200 MPa and compressive of 660 MPa. a. What force in lbs acting at the pulley rim will shear the key?b. What force in lbs acting at the pulley rim will crush the key?