Three wye-connected load impedances, 15260° N, Z, 202 - 30° SN, and Z. 10245° 2, are connected to an abc- || %D sequence, balanced 3-phase, wye-connected source with a line voltage of 208 V. A conductor of impedance 1 + j5 Q is used to connect together the neutral points of the source and the load. The line impedance per phase is 4 + j202. Calculate the load phase currents and voltages, and the neutral current.

Three wye-connected load impedances, 15260° N, Z, 202 - 30° SN, and Z. 10245° 2, are connected to an abc- || %D sequence, balanced 3-phase, wye-connected source with a line voltage of 208 V. A conductor of impedance 1 + j5 Q is used to connect together the neutral points of the source and the load. The line impedance per phase is 4 + j202. Calculate the load phase currents and voltages, and the neutral current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
A delta connected load with Zab=3 + j2 Ohm, Zbc=3 + j4 Ohm and Zca=2 + j3 Ohm are connected the end of a three-phase line as shown in the figure. The line impedance is 1+j2 Ohm per phase. The line is supplied from a three-phase source with line-to-line voltage of Vab=200.0/0° V rms. Taking the phase current vector lab as the reference vector, determine; (a) Line current Ia. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal. ao- bo- Co- 1+j2 b a
In a balanced Y-Y circuit shown in Figure 5, the magnitude of the phase voltage at the source is Vp = 2520 V (rms) and Van = 252020° V (rms). The load impedance is Zy = 135 + j55 Q per phase and the wire impedance is Zw=85 + j65 per phase. All the voltages and currents are in rms in this problem. (a) Find the phasors for line currents IA, IB, Ic in rms. (b) Find the load voltage VAN = IAZY. Also find VBN, and VCN. (c) Find the line voltages VAB, VBC, VCA at the load. (d) Find the complex power SL of the load. ZW ZY Van a A IA ZW ZY Vbn b В IB N ZW ZY Vcn IC Figure 5
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
Suppose that a current source with Is amperes of current is connected in parallel to a pair of impedances Z₁ and Z2. Let I₁ be the current through Z₁ and 12 be the current through Z₂. Then, the total voltage Is is divided between 1₁ and 12 in proportion to impedance values Z₁ and Z2. a. True O b. False
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
A 30-0 resistor, a 15-02 inductive reactance, and a 12-02 capacitive reactance are connected in parallel across a 120-V 60-Hz line. Find (a) the phasor branch currents, (b) total current and phase angle, (c) impedance, and (d) power drawn by the circuit.
Figure Q2(a) shows a positive sequence three phase circuits. Given a line-to-line voltage at generator, ERY = 415230°V. With assumption that all load impedance are balanced, Zn=Zyb=Zbr= 15 + jl8 2, determine all phase currents at each load and line currents. Include the phasor diagram for all currents in your analysis. R Zry Zyt Figure Q2(a) If the transmission line in three phase circuit at Figure Q2(a) has a impedance of 1+j20 for each phase, determine the phase voltages for each load with using an appropriate analysis. Use phase voltage at generator, ERN as a reference. Then determine the total apparent power, active power and reactive power supplied by the generator.
A balanced positive-sequence three-phase source hasvan(t)=100 cos(377t+90°) V a. Find the frequency of this source in Hz. b. Give expressions for vbn(t) and vcn(t) c. Repeat part (b) for a negative-sequence source.
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.