There are two main types of water distribution system layouts. In the Answer system, the main line is connected back to itself and the smaller lines join the main line at two or more locations. In the Answer system, a main distribution pipe is used, and smaller lines are connected to the main line at only one point along the length of the main line. The Answer is preferred over the because it has isolation valves and water flows in more than one direction, which can avoid having to shut off water to all customers in an area during repairs. branched system series Answer looped looped system parallel branched

There are two main types of water distribution system layouts. In the Answer system, the main line is connected back to itself and the smaller lines join the main line at two or more locations. In the Answer system, a main distribution pipe is used, and smaller lines are connected to the main line at only one point along the length of the main line. The Answer is preferred over the because it has isolation valves and water flows in more than one direction, which can avoid having to shut off water to all customers in an area during repairs. branched system series Answer looped looped system parallel branched

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Minor Losses A pipe system is comprised of a flush entrance, one gate valve, one 90° elbow, one 45° bend, and a globe valve. If the fluid flows at 11 ft/s, what is the head loss due to minor losses? O 12.4 ft O 14.3 ft O 22.5 ft 13.2 ft O 8.55 ft O 6.60 ft
characteristics of the two pipe system configurations (series and parallel) in terms of discharge, headloss and relationship between pipes in the system.
It is an underground pipe that receives the runoff from roadside inlet. O Sewerage Pipe o culverts O subsurface Drainage O Storm Sewer
Assignment 4. Date =18/05/2022 Q7 For the branching system as shown in figure. Calculate the discharge in each pipe. Take f 0.02 for all pipeline. EL: 126.00 m EL: 109.00 m EL: 100.00 m A C Pipe Dia (cm) 1 15 2 10 3 10 (Neglect minor losses) Length (m) 350 200 250 B Connectivity AJ BJ JC
10 Pump test system problem:. For the pump test arrangement shown in figure below, determine the mechanical efficiency of the pump if the power input is measured to be 3.85 hp when pumping 500gal/min of oil (y = 56.0 lb/ft3). (1 hp = 33,000 lb-ft/min or 550 lb-ft/s.) %3D %3D FROM SUPPLIER TABLE FOR Particular Pipe such as Schedule 40, With Certain DN value, OD and Wall thickness are given as below. Wall Flow Flow NO Thickness re. (i) 4.500 (u) calculate Pump 0.237 calculate 4. 6-in Schedule 40 4-in Schedule 40 calculate 6.625 0.280 calculate 9. +2 (y = 56 lb/ft) 20.4 in wer Mercury (sg D13.54)
Methanol (SG = 0.8335, viscosity is equal to that of water) is being transported from a very large reservoir and is entering at a standard 1.25-in 540 pipe at an absolute pressure of 14.7 psia. The methanol is transported at a total of 1450 ft and passes through 15 standard ells, 5 gate valves (open), 6 tees (standard), and 4 tees (as ell, entering branch). The methanol is discharged 22 ft above the inlet at a gauge pressure of 8 psig. If the fluid flows at a rate of 30 gpm and the pump have an efficiency of 50%, calculate the actual power needed in kW.
What is the discharge in pipe 1? A. 0.61 B. 0.90 C. 0.49 D. 0.68
The 6 inch pipeline as shown conducts water from a reservoir and discharges at a lower elevation through a nozzle which has a discharge diameter of 2 inch. The water surface in the reservoir (1) is at elevation 100 ft and the pipe intake ( 2 and 3) at elevation 80 ft and the nozzle ( 4 and 5 ) at elevation 0. The head losses are: from 1 to 2, 0 ft; from 2 to 3, 2 ft; from 3 to 4, 30 ft; from 4 to 5, 10 ft. Compute the discharge and make a table showing elevation head, velocity head, pressure head and total head at each of the five points.
Fluid flows through a 20-mm diameter pipe, 150-m long at a Reynold's number of 1750. Calculate the discharge if the head lost is 175- m.
A cylindrical tank has a radius of 5 ft and a height of 13 ft. Set up an integral to determine how much work is done in emptying it if(a) It is filled with molasses (which weighs 235 lb/ft3).(b) It is filled to a depth of 9 ft and the molasses must be pumped out a 2 ft pipe at the top of the tank.
Wastewater pipe with 70 m length, 4% slope, n= 0.014, d/D is 0.65 and 10" diameter, estimate the followings Vp/VfD Qp/Qf= m/sec Vfull= m/sec Qfull= Liter/sec V%3D m/sec Qp= Liter/sec
Mechanical Draft Cooling Tower - Draw the Process Flow Diagram, and develop Piping & Instrumentation Diagram P&ID of any one process from this industry.