The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the sleeve (3) (Øinner = 10, Øoutside = 15) also made of steel and two rivets at the points shown. The shaft (1) is firmly clamped on the left- hand side, the force F = 100 N acts on shaft 2 in the direction of the arrow. How are the brass round rivets to be dimensioned so that a safety of the coupling against failure of S = 10 is achieved? hole for rivets 2 F 3 a) What type of connection does a riveted connection have? b) What type of load does the rivet have? c) What is the diameter of the rivets? d) Which areas of the rivet are loaded? (Draw in figure and formula) e) Dimension the rivet

The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the sleeve (3) (Øinner = 10, Øoutside = 15) also made of steel and two rivets at the points shown. The shaft (1) is firmly clamped on the left- hand side, the force F = 100 N acts on shaft 2 in the direction of the arrow. How are the brass round rivets to be dimensioned so that a safety of the coupling against failure of S = 10 is achieved? hole for rivets 2 F 3 a) What type of connection does a riveted connection have? b) What type of load does the rivet have? c) What is the diameter of the rivets? d) Which areas of the rivet are loaded? (Draw in figure and formula) e) Dimension the rivet

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If P is equivalent to 94 kN, the diameter at pin B is Blank 1 mm.
The bar in the attached picture has a thickness of 16mm and a total width of 48mm. The pin has an diameter of 11mm.....
The lap joint is fastened with four ¾-inch diameter rivets. a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. c. what is the maximum value of the load P (kips) that can be applied to the joint?
Q.2) The cylinder consists of spirally wrapped steel plates that are welded at the seams in the orientation shown. Assume B=620. The cylinder has an outside diameter of 265 mm and a wall thickness of 7 mm. The ends of the cylinder are capped by two rigid end plates. The cylinder is subjected to tension axial loads of P = 45 kN and torques of T = 51 kN-m, which are applied to the rigid end caps in the directions shown. Determine (a) the normal stress perpendicular to the weld seams. (b) the magnitude of the shear stress parallel to the weld seams. (c) the absolute maximum shear stress on the outer surface of the cylinder. T P T
Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel. Two rivets, one in front and one in back, secure the ends of each step. The rivets attach the steps to the left and right hand rails. A 225 lb person stands in the center of a step. If rivets are formed of 6061-T6 aluminum, what should be the diameter d of the rivets? Use a factor of safety of 8 and round your answer to the nearest 1/16 of an in.
3. JA beam is welded to a wall and subjected to a force couple (torsional moment) of 12000 in-lbs and a tensile force of 5000 lbs as shown. The cross-section is circular with an outer diameter of 4 inches. The weld is all-around. The electrode is E60 and the weld leg is 4 inch. The factor of safety guarding against static yielding is closest to: a. 1.5 b. 2.2 с. 3.9 12000 im-lb d. 4.5 e. 5.3 5000 lbs 94* Weld
find the bearing stress between bolts and plate 10/-.. 5. 1) 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 1O MM ------- -O- O 300mm 8 mm
Downvote for incorrect answer The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (b)allow 2 ksi, and the allowable tensile stress within the bolt shank S is (allow 18 ksi, determine the maximum = allowable tension in the bolt shank. The bolt shank has a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across section B, the compressive stress between the pin and the rod, and the compressive stress between the pin and the yoke. Given n = 1 (3 / 4) in., a = (15 / 32) in., e = (27 / 32) in., b = (15 / 16) in., d = (19 / 32) in., f = 1".
For a lap joint, determine the maximum safe load P which may be applied if the shearing stress in the rivets is limited to 60 MPa, the bearing stress in the plates to 110 MPa, and the average tensile stress in the plate to 140 MPa