The three suspender bars AD, BE, and CF are made of the same material (E = 70 GPa) and have equal cross-sectional areas of 450 mm². The rigid beam is subjected to the loads P, (KN) and P, (KN) as shown. Analyze the system of axial bars if the allowable stress requirement and axial deformation limitations are satisfied. Each bar must not exceed the allowable stress of 90 MPa and axial deformation of 4.0 mm. B FICHICHIN H-+-+ 2 m D

The three suspender bars AD, BE, and CF are made of the same material (E = 70 GPa) and have equal cross-sectional areas of 450 mm². The rigid beam is subjected to the loads P, (KN) and P, (KN) as shown. Analyze the system of axial bars if the allowable stress requirement and axial deformation limitations are satisfied. Each bar must not exceed the allowable stress of 90 MPa and axial deformation of 4.0 mm. B FICHICHIN H-+-+ 2 m D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Determine the largest weight W that can be supported by the two wires AB and AC. The allowable working stresses are 180 MPa for AC and 120 MPa for AB. The cross-sectional area of AB is 500 mm2 and that of AC is 300 mm2. Show the solution. Correct answer is 60.23kN
The cross section of a steel beam is constructedof a W 18 × 71 wide-flange section with a 6 in. × 1/2 in.cover plate welded to the top flange and a C 10 × 30channel section welded to the bottom flange. This beamis subjected to a bending moment M having its vector atan angle θ to the z axis (see figure).Determine the orientation of the neutral axis andcalculate the maximum tensile stress σt and maximumcompressive stress σc in the beam. Assume thatθ = 30° and M = 75 kip-in. Note: The cross- sectionalproperties of this beam were computed in ExamplesD-2 and D-5.
The rigid beam is supported by the three suspended bars. Bars AD andCF is made of A-36 steel and BE is made of 2014-T6 aluminum alloyeach having a cross-sectional area of 450mm2. Determine the angle oftilt of the rigid beam DEF and the average normal stress in each bar ifthe rigid beam is subjected to the loadings shown. Take ESt = 200 GPa and EAl = 73.1 GPa.
Problem 1 Please choose the correct answer and also write down your solution. (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress at A and B? P P a. Both og and og are tensile stress. 0.5 m 0.5 m 0.5 m b. Both oa and og are compressive stress. Og is tensile stress and og is compressive stress. с. d. OA is compressive stress and og is tensile stress. A В (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 a. 7/2 d. 2/10 е. 3/10 h. 10/3 c. 7/3 f. 10/2 i. 1/1 g. 2/7 250 mm 20 mm 60 mm 200 mm 2 m 1 m 15 mm 15 mm
Solve using Method Of Consistent Deformation. (indeterminate beam) Please provide Compatibility Equation and step by step solution .
solve for the compressive strength for the specified column:
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
Try to write out the stress boundary conditions of the cantilever beam. (not include the fixed edge) pgy y -30° b/2 b/2 (h>>b,8 =1) x
a.what is the maximum bending stress fbx (MPa) in the girder b.determine the maximum bending stress fby (MPa) in the girder c.using interaction formula fbx/Fbx + fby/Fby
The lap joint as shown is fastened by the 20mm diameter rivets. Assuming that the load P=50kN, determine (a) Shearing stress in each rivet, (b) Bearing stress in each plate, (c) Average tensile stress in the plateProvide complete solution pls.
3- Use the direct stiffness method to set-up and solve the problem for the following beam structure: P E, I, L E, I, L Hinge