The potentiometer which is used to measure angular displacement has a total resistance of 3.8kn with a maximum angle of rotation as 336.4 degree and connected with dc power supply of 10.73V. Then the change in resistance is calculated as, O a. 0.96 K ohms O b. 1.38 K ohms O C. 2.45 K ohms O d. 2.12 K ohms

The potentiometer which is used to measure angular displacement has a total resistance of 3.8kn with a maximum angle of rotation as 336.4 degree and connected with dc power supply of 10.73V. Then the change in resistance is calculated as, O a. 0.96 K ohms O b. 1.38 K ohms O C. 2.45 K ohms O d. 2.12 K ohms

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
In the following figure find sa Asa turns ratio is A.O-7E A.07001
5 The voltmeters in the figure measure RMS voltages. If V, = 23 V and V, = 14.5V what is V3? %3D C R eee V2 V3 23 V None of them 8.5 V 4.5V 37.5 V O 14.5 V
Millmans theory current thru 5ohm
3. Sketch the current waveform for the circuit in Figure below. The diac has a breakover potential of 20 V. IH = 20 mA. 25 V rms R 1.0 ΚΩ
Consider the following statements :A clamper circuit 1. adds or subtracts a dc voltage to a waveform 2. does not change the waveform 3. amplifies the waveform Which are correct? * O 1,2 O 1,3 O 1, 2, 3 O 2,3
Problem: 25 mH m Find Leq In below figure. 10 mH m 60 mH m 20 mH m 30 mH m -o b L 0000
M EXPERIMENT 01 V(n002) V(n001) 10V- 8V- 6V- 4V- 2V- OV- -2V- 4V- -6V- -8V- -10V- 0.00ms 30.00ms 60.00ms 90.00ms 120.00ms 150.00ms 180.00ms K EXPERIMENT 01 X Diode 1N914 V Resistor SINE(0 10 60000 100) 10K .tran 2
Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 Vusing a single 14 V dc voltage source
The attached image shows a circuit with an AC voltage source, a resistor, inductor, and capacitor connected in series. The circuit has the following characteristics: Resistor resistance: 10 ohm Capacitor capacitance: 0.05 F Inductor inductance: 13 H Current Amplitude: 4 A Voltage amplitude across the source: 60 V Frequency at the source: 0.3 Hz Voltage amplitude across the resistor: 35 V Voltage amplitude across the capacitor: 37 V Voltage amplitude across the inductor: 80 V (a) Calculate the RMS voltages from the amplitudes above. From the RMS voltages across the capacitor, inductor and resistor, calculate the RMS voltage of the AC source. Hint: Vrms = V0/sqrt(2) Vrms = sqrt( (Vrms,R)2 + (Vrms, L - Vrms, C)2 ) (b) Calculate the RMS value of the current (c) Using the resistance, capacitance, inductance, and the frequency of the AC voltage, calculate the impedance Z. From this, and the previously measured value of Vrms, find the RMS value of the current in the circuit.
A step up chopper has input voltage 110 V and output voltage 150 V. The value of duty cycle is.