The oscilloscope is switched to XY mode of operation. V, is connected to the X input with sensitivity 0.1 V/div, and V2 is connected to the Y input with sensitivity 0.2 V/div. (Note: the division here is the major division.) The resulting ellipse is shown in Fig. 7.18. Calculate Ym Yo- -Yo Fig. 7.18 Xo a. The values of Ym, Yo, Xm, and Xo. b. Phase shift between signal in X and signal in Y. c. Peak-to-peak values of voltage for V1 and V2.

The oscilloscope is switched to XY mode of operation. V, is connected to the X input with sensitivity 0.1 V/div, and V2 is connected to the Y input with sensitivity 0.2 V/div. (Note: the division here is the major division.) The resulting ellipse is shown in Fig. 7.18. Calculate Ym Yo- -Yo Fig. 7.18 Xo a. The values of Ym, Yo, Xm, and Xo. b. Phase shift between signal in X and signal in Y. c. Peak-to-peak values of voltage for V1 and V2.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

See Fig 565, may not be drawn to scale, but it is representative of the curve, which is described by V(t)=Vm*sin(w*t+theta) + Vshift. Given V1=30, V2=-35, V4=-18.750 volts, and t3=1.4 msec. Find Vm (volts), w (rad/sec), theta (deg), Vshift, and t4 (msec). just need t4 1 Vm 32.5 32.5 volts 2 w 8975.98 8975.98 rad/sec 3 theta 90 90 deg 4 Vshift -2.5 -2.5 volts 5 t4
The velocity olistribution is Ve 2xî - ayj + (3t-bz k). Is it steady? Find the eg. of the stream lines through the pt. (1,1,3) at t=o,1.
If the current in the Helmholtz coils were 1.6 A, rather than 1 A, and the accelerating voltage were still 100 V, what would the radius of the electron's path be? Give your answer in cm, and enter only the number. Blackboard will accept an answer witin 20% of the value it expects.
Answers must be expressed in engineering notation (when the exponent of the base ten multiplier is not a multiple of 3, press ENG or SHIFT+ENG, whichever the case.) Example: 0.06N or 6.0x10² N must be expressed to 60x10-³N or 60mN 1. Consider a beam of electrons that moves from the electron gun towards the screen of a cathode ray tube due to the potential difference of 15kV. A pair of coils are placed outside a cathode ray tube and produce a uniform magnetic field of 250 μT across the tube. Calculate the force experienced by the electrons if the magnetic field is in place: a. parallel with the direction of the beam. b. Perpendicular with the direction of the beam. c. 50 degrees with the direction of the beam.
.Q6.Consider the following truth table and determine the SOP expression. Also convert it into equivalent POS. A B C OUTPUT 0. 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Find the minimum acceleration needed for a maglev train to reach a speed of 430 km/h in 3.0 km, one tenth of the length of the 30-km track in Shanghai. Express your answer as a fraction of g, the free-fall acceleration near Earth. Would this acceleration be noticeable
grdeperdent w. of a partile of a The nowingm 4x 4 ip polential maRe mou le a Condat expE ちく $ind the % * the lan plem energ of
26.10. Please help with part A and B of this problem. thank you!
Question related to Quantum Mechanics : Problem 1.16
Could you please check my answer is correct? This is not a test problem. Just a HW problme. please don't reject it. No one post test problem at 11 pm. I'm just so comfused with this one and want to know detail explanation. Thank you!!
4. During charging of the capacitor in Fig. 4.1, both the voltage [Ve(t) = q(t)/C] at the capacitor and the voltage at the resistance [VR(t) = ic(t)R] change with time. Let us consider a charging circuit that has C = 1F, and e = 5 V. Charging starts at time, t = 0, and it is found that, V. becomes equal to VR at 4.16 s after the charging starts. Based on this information, what is the value of R, in this circuit? Show all steps of your calculation.
One cycle of the signal on the oscilloscope screen has width of 2.8 cm (1 division = 1 cm). The setting on the Horizontal TIME/DIV control is 2 us. The period of the signal is us. Write your answer in the tenths place. Only the numerical value will be graded. One cycle of the signal on the oscilloscope screen has width of 2.8 cm (1 division = 1 cm). The setting on the Horizontal TIME/DIV control is 2 us. The frequency is kHz. Write your answer in the tenths place. Only the numerical value will be graded.