The normal strain measured on the outside surface of a spherical pressure vessel is 670 με. The sphere has an outside diameter of 1.20 m and a wall thickness of 10 mm, and it will be fabricated from an aluminum alloy [E = 73 GPa; ν = 0.33]. Determine (a) the normal stress in the vessel wall and (b) the internal pressure in the vesssel

The normal strain measured on the outside surface of a spherical pressure vessel is 670 με. The sphere has an outside diameter of 1.20 m and a wall thickness of 10 mm, and it will be fabricated from an aluminum alloy [E = 73 GPa; ν = 0.33]. Determine (a) the normal stress in the vessel wall and (b) the internal pressure in the vesssel

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.7P: A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the...

See similar textbooks

Similar questions

A steel plate is subjected to a state of plane stress (E = 200 GPa and v = 0.29) of Oxx = 105 MPa, Oyy = -19 MPa and Oyy = 96 MPa. Calculate the axial strain, ɛ77, at this point in the z direction, normal to the plate's surface. Provide your answer in microstrain, pɛ. You do not need to type the units.
Q2 A rod is 3m long at a temperature of 15°C. Find the expansion of the rod, when the temperature is raised to 95°C. If this expansion is prevented, find the stress induced in the material of the rod. Take E=1x105 N/mm2 and α=0.000012/°C.
mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
A 23 mm diameter bronze bar 2.8 m long is placed between two rigid walls. At a temperature of -3°C, the gap Δ = 4.6 mm. Find the temperature(at degree-Celsius) at which the compressive stress in the bar will be 34 MPa. Use α = 18.09 × 10-6 m/(m·°C) and E = 82 GPa. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.
A steel rod 3 ft long with a cross-sectional area of 0.3 in2 is stretched between two fixed points. The tensile force in the rod is 1200 lb at 40°F. Using α = 6.5 x 10-6/°F and E = 29 x 106 psi, calculate the temperature (in °F) at which the stress in the rod will be zero.
A weight of 300 N is suspended below a horizontal beam by means of two wires at angles of 30 ° and 45 ° to the horizontal as shown below. The Young's modulus of the both wires is E=200,000 MN/m². The cross sectional area of the left wire is 40mm2 while for the right wire it is 50mm². Select the correct answer for the direct stress in the left wire. Give your answer in N/mm2 to three decimal places. Assume tension to be positive and compression negative. 30° 45° (Not to scale) 2m 300 N O 6.725 O 5.490 O 4.392 O 5.380
The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
Determine the change in the volume of a 10 cm diameter copper sphere that is subjected to a hydrostatic pressure of 120 MPa assuming linear elastic behavior up to this stress level. (V=4/3 t r') (E= 125 GPa, v = 0.34, Sy = 200 MPa)
A vessel is pressurised at A. The ends of the vessel are shut with two-disc plates connected by the shaft BC. The internal gauge pressure is 6.8 MPa. The Young's modulus is 210 GPa, the inner radius of the vessel is 80 cm, and the wall thickness is 12 mm. 1. Determine the change in the diameter of the vessel. 80 cm 12 mm 12 cm C
The bar shown in diagram is subjected to a tensile load of 150 kN. If the stress in the middle portion is limited to 160 N/mm2, determine the diameter of the middle portion. Find also the length of the middle portion if the total elongation of the bar is to be 0.25 cm. Young's modulus is given as equal to 2.0 × 105 N/mm2. 150 KN ➜ 10 cm DIA 45 cm 10 cm DIA 150 KN
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression vy/3E where y = 2.3 lb/in.³ is the specific weight of the material, y = 0.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 8 in. is the length of the bar, and E = 23000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar.
A gas is stored in a cylindrical tank of inner radius 7 m and wall thickness 50 mm. The gage pressure of the gas is 2 MPa. The maximum shear stress (in MPa) in the wall is