The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN, determine the magnitudes of the average normal stress in the shank, the average shear stress along the cylindrical area of the plate defined by the section lines a-a, and the average shear stress in the bolt head along the cylindrical area defined by the section lines b-b. Answers should be in MPa. 8 mm a 7 mm 8 kN 18 mm a 30 mm

The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN, determine the magnitudes of the average normal stress in the shank, the average shear stress along the cylindrical area of the plate defined by the section lines a-a, and the average shear stress in the bolt head along the cylindrical area defined by the section lines b-b. Answers should be in MPa. 8 mm a 7 mm 8 kN 18 mm a 30 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 20-mm-thick plate is bolted to the flange of a T-beam to form a 200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm
A plate with width of 300 millimeters and thickness of 20 milimeters is to be connected to two plates of the same width with half the thickness by 25 millimeters by 25 millimeters diameter rivets. The rivets holes have a diameter 2 millimeters larger than the rivetdiameter. The plate is A36 with yield strength F, = 248MP.. Allowable tensile stress on net area is 0.6Fy and allowable bearing stress of 1.3Fy. The rivets are A502, Grade 2, hot-driven rivets with allowable shear stress of 150MPA. 1. Detemine the maximum load that can be applied to the connection with consideration to the yielding failure in the plates. 2. Detemine the maximum load that can be applied to the connection with consideration to the fracture failure in the plates. 3. Detemine the maximum load that can be applied to the connection without exceeding the allowable shearing stress in the rivets. 4. Detemine the maximum load that can be applied to the connection without exceeding the allowable bearing stress between…
20MPA a In Figure , according to the stress condition of a stack of I-section beam. (30Mpa is the shear stress value.) 30MPA I- 40MPа 1-)Calculate the principal stresses, location and angle. A 2-)Calculate the stress components that will affect the plane in a section a-a that makes a 300 angle shown in the figure.
Q2. Design a rivet that is utilized in a double riveted butt joint which connects two 12 mm thick plates. The efficiency of riveting joint is 80% and the pitch is 80 mm. If the allowable stresses for the plate material are (tensile stress o 100 MPa, shear stress - 75 MPa, bearing stress oc= 180 MPa) and for the rivet material are (tensile stress o-120 MPa, shear stress T-90 MPa, bearing stress 6 = 200 MPa), use F.S. = 1.
The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)
What is the minimum required bolt diameter (mm) at C ifthe allowable bolt shear stress is 68 Mpa.a. 9 mm c. 11 mmb. 10 mm d. 12 mm Determine the stress (Mpa) in strut BC.a. 5.6 MPa c. 3.2 MPab. 2.8 MPa d. 6.4 MPa Calculate the bolt stress (Mpa) at A if its diameter is 20mm.a. 7.64 MPa c.11.46 MPab. 3.82 MPa d.14.92 MPa
2m 2m 12₂ 2m y 2N/m ✓ 2N/m 2m $ بلا
ABDE rigid rod with single action rivet from point A, point B Connected with BC rod. B and C points of the rod are fence effect rivets. The maximum shear stress that the rivets can bear is 550 MPa, that of the BC bar Since the maximum tensile stress is 440 Mpa, the safety factor FS = 2; 1 ) Calculate the diameter of rivets A and B 2 ) Calculate the diameter of the BC rod
The gusset is riveted to a larger plate by 4 – 22mm rivets in single shear arranged andloaded as shown. Calculate the stress in the most heavily loaded rivet.
Mechanics of Deformable Bodies Two forces are applied to the bracket BCD as shown. Knowing that the control rod AB is to be made of steel having an ultimate normal stress of 650 MPa, and the pin at C is to be made of steel having an ultimate shearing stress of 400 MPa, determine: (a.)The diameter of the rod for which the factor of safety with respect to failure will be 3.0. (b.)The diameter of the pin C for which the factor of safety with respect to shear will also be 3.0
If the eyebolt is made of a material having a yield stress of Y = 275 MPa and the factor of safety F.S. = 1.45 against yielding, determinea. allowable stress in the eyebolt.b. minimum required diameter d of its shank.
Assume that two 8-mm-diameter bolt joins the plates that are each 175 mm wide. The allowable stresses are 120 MPa for bearing in the plate material and 60 MPa for shearing of bolt. Determine (a) Safe Value of P, (b) the minimum thickness of each plate; (c) the largest tensile stress in the plates.