The linkage is made of two pin-connected A-36 steel members, each having a cross-sectional area of 1.4 in². (Figure 1) Figure 2 ft B 1151-151- 1 of 1 Part A Determine the magnitude of the force P needed to displace point A 0.035 in, downward Express your answer in kilopounds to three significant figures. 1951 ΑΣΦ 11 Ivec P-1421 Submit Previous Anawers Request Anawer X Incorrect; Try Again; 5 attempts remaining Provide Feedback ? kip No:

The linkage is made of two pin-connected A-36 steel members, each having a cross-sectional area of 1.4 in². (Figure 1) Figure 2 ft B 1151-151- 1 of 1 Part A Determine the magnitude of the force P needed to displace point A 0.035 in, downward Express your answer in kilopounds to three significant figures. 1951 ΑΣΦ 11 Ivec P-1421 Submit Previous Anawers Request Anawer X Incorrect; Try Again; 5 attempts remaining Provide Feedback ? kip No:

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 80.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.70 MN, pressure vessel bolts aide port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm.
When force P is apliced to the rigid arm BC, point B moves downward 0.2mm. Determine the enlongation developed in wire CD: ___ mm. Calculate your answer to 2 digit place.
asap
1. Note: for part a), you can do this without a calculator; it might be easier to work out the problem symbolically, and then substitute the numbers at the end of the problem. В 2L The axial rod is fixed to the two walls, as shown above. Portion AB is composed of one material (EAB = E), while portion BD is composed of a different material (EBD = 2E). Portion AB has cross sectional area AAB = A, while portion BD has cross sectional area ABD = 2A. EAB = E = 15×106 psi AAB = A = 1 in² EBD = 2E = 30×10° psi ABD = 2A = 2 in² LAB = L = 10 in. LBC = 2L = 20 in. LcD = L = 10 in. An external force, P = 100 kips, is applied at point C as shown below. a) Determine the reaction forces at wall A and D, Ra and Rp. Specify the direction, (→) or (+). b) Deflection at point C. Specify the direction, (→) or (+). (Ans: RA = 100/7 kips →, Rp = 600/7 kips →, & = 1.429x10² in –)
For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and y2 = 0.33 m. Find the moment of inertia about the horizontal axis where y=0 (bottom of the cross-section). Report your answer in units of m4 to four decimal places. y y2 x1 2 (no answer) Correct Answer: 0.002021
Set P₁= 2 kN and P₂ = 1.5 kN. (Figure 1) Figure 30° -3m D 30° 3m 1 of 1 Copyright @ 3032 D.
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 48512-Nload, using the following data: length of steel = 1.42 m, length of bronze = 2.36 m Area of steel = 639 mm, Area of bronze = 319 mm Modulus of elasticity of steel = 180 Gpa, Modulus of elasticity of bronze = 81 Gpa x = 0.58 m, y = 1.13 m, and z = 0.72 m. Round off the final answer to two decimal places.
GIVEN: W= 595 N GIVEN: ANGLE A= 44 DEGREE GIVEN: ANGLE B= 14 DEGREE ANSWER: SOLVE (A) IN UNIT CM SOLVE (B) IN UNIT N-CM SOLVE (C) IN N-CM PLS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY AND SHOW THE FREE BODY THE DIAGRAM
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 360.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.30 MN. pressure vessel W bolts side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. cm x10 X
An engineer determines that a 60 cm long rod of 1045 HR grade of steel will be subjected to a tension of 20kN. The following two designs requirements must be met: must remain below 145MPa and the rod must stretch less than 0.125mm. Determine an appropriate value for the rod's diameter to meet these two requirements. Round to the nearest milimeter
F1=603N F2 =818N show a detailed solution please
GIVEN: W= 595 N GIVEN: ANGLE A= 44 DEGREE GIVEN: ANGLE B= 14 DEGREE ANSWER: SOLVE (A) IN UNIT CM SOLVE (B) IN UNIT N-CM SOLVE (C) IN N-CM PLS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY AND SHOW THE FREE BODY THE DIAGRAM PLS TAKE NOTE OF THE UNITS WHICH ARE IN CM NOT IN MM AND ALSO LOOK AT WHAT SHOULD BE THE UNITS IN SOLVING (A) IN UNIT CM IN (B) IN UNIT N-CM AND IN (C) IN N-CM.