The concentration of H2S in wastewater samples was determined by coulometric titration using Kl as mediator and I3 as "titrant". standard concentration Peak area (a.u) (ppm) 50 8354 100 16925 150 25218 200 33584 250 42002 A 50 mL wastewater sample was placed in a coulometric cell, added with excess KI and starch indicator. Electrolysis was carried out at a constant current of 84.6 mA for 386 s to reach the end point of the titration. What is the concentration of H2S in the sample (in ppm)?

The concentration of H2S in wastewater samples was determined by coulometric titration using Kl as mediator and I3 as "titrant". standard concentration Peak area (a.u) (ppm) 50 8354 100 16925 150 25218 200 33584 250 42002 A 50 mL wastewater sample was placed in a coulometric cell, added with excess KI and starch indicator. Electrolysis was carried out at a constant current of 84.6 mA for 386 s to reach the end point of the titration. What is the concentration of H2S in the sample (in ppm)?

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter22: Bulk Electrolysis: Electrogravimetry And Coulometry

Section: Chapter Questions

Problem 22.28QAP

See similar textbooks

Similar questions

Table 17-1 lists common half-reactions along with the standard reduction potential associated with each half-reaction. These standard reduction potentials are all relative to some standard. What is the standard (zero point)? lf is positive for a half-reaction, what does it mean? If is negative for a half-reaction, what does it mean? Which species in Table 17-1 is most easily reduced? Least easily reduced? The reverse of the half-reactions in Table 17-1 are the oxidation half-reactions. How are standard oxidation potentials determined? In Table 17-1, which species is the best reducing agent? The worst reducing agent? To determine the standard cell potential for a redox reaction, the standard reduction potential is added to the standard oxidation potential. What must be true about this sum if the cell is to be spontaneous (produce a galvanic cell)? Standard reduction and oxidation potentials are intensive. What does this mean? Summarize how line notation is used to describe galvanic cells.
At 298 K, the solubility product constant for solid Ba(IO3)2 is 1.5 109. Use the standard reduction potential of Ba2+(aq) to find the standard potential for the half-reaction Ba(IO3)2(s)+2eBa(s)+2IO3(aq)
When jump-starting a car with a dead battery, the ground jumper should be attached to a remote part of the engine block. Why?
The iron content of hemoglobin is determined by destroying the hemoglobin molecule and producing small water-soluble ions and molecules. The iron in the aqueous solution is reduced to iron(II) ion and then titrated against potassium permanganate. In the titration, iron(ll) is oxidized to iron(III) and permanganate is reduced to manganese(II) ion. A 5.00-g sample of hemoglobin requires 32.3 mL of a 0.002100 M solution of potassium permanganate. The reaction with permanganate ion is MnO4(aq)+8H+(aq)+5Fe2+(aq)Mn2+(aq)+5Fe3+(aq)+4H2O What is the mass percent of iron in hemoglobin?
1. Calcium in a sample solution is determined by atomic absorption spectroscopy (AAS). A stock solution of calcium is prepared by dissolving 1.834 g CaCl, 2H,0 in water and diluting to 1 litre. From this stock solution, the second stock solution is prepared by the dilution factor of 10. Three standard solutions of calcium are prepared from the second stock solution with the following dilution factor: 20 (first standard solution), 10 (second standard solution) and 5 (third standard solution). A blank solution is prepared as well. Absorbance signals of AAS are as follows: 1.5 (blank solution), 10.6 (first standard solution), 20.1 (second standard solution), 38.5 (third standard solution), 29.6 (sample solution). (Molar mass; Ca = 40.00 g mol-, CI = 35.45 g mol-, 0 = 16.00 g mol-', H = 1.00 g mol-1) a. Construct ONE (1) plot that could be used to represent the calibration curve. b. From the plot of Q1a, determine the amount of calcium in parts per million.
30jud to 28AM basu mw 5. Sodium carbonate is a reagent that may be used to standardize acids in the same way that you have used KHP in this experiment. In such a standardization it was found that a 0.498-g sample of sodium carbon- ate required 23.5 mL of a sulfuric acid solution to reach the end point for the reaction.
1. Copper is found as the mineral covellite (CuS). The first step in extracting the copper is to dissolve the mineral in nitric acid (HNO3), which oxidizes sulfide to sufate and reduces nitric acid to NO: CuS) + HNO3(aq) → NO(g) + CuSO4 -> Balance this equation using the half- reaction method CHEM GINEE RST YEAR FRANE 6 hra
Toxie chromate can be removed from solution uning the following reaction 2 Cro, lag) + 3SO4H'(ag)- Cry(SOls) + 2HyOA 5o, Is bubbled through 3.0x 10Lofa solution. All of the chromate is removed and 2.94 x 10 kg of the precipitate is formed. Calculate the initial concentration (in units of mM) of chromate in solution. Write only the numerical value below (without units) using the correct number of signihcant hpares. Type your answer Nest
Five white, 500-mg uncoated ascorbic acid (AA) tablets with an average weight of 0.6152-g were pulverized in a mortar. A sample of the powdered ascorbic acid weighing 0.4700-g was placed in an iodine flask and was dissolved in 50-mL H2SO4 then 5-g of KBr was added to the resulting solution. The solution was titrated with 47.81-mL of 0.09640 N STD. KBrO3 to reach a faint yellow endpoint then 3-g KI and 5-mL Starch TS. The blue color solution is then titrated with 2.73-mL of 0.09123 N STD. Na2S2O3 to reach the disappearance of the blue iodostarch complex. MW: KBrO3 = 167.0 ; KIO3 = 214.0 ; Na2S2O3 = 158.11 ; C6H8O6 = 176.12 Compute the milligrams of pure AA per tablet from the assay. 293.3 mg 502.5 mg None of the choices 383.9 mg
A 0.2500-g of dry CaCO3 was completely dissolved into a solution of 5-mL conc. HCl and 50-mL distilled water in an erlemeyer flask. The resulting solution was boiled for 5 minutes to expel CO2 from the reaction, and then it was cooled to room temperature and the solution was transferred in a 500-mL volumetric flask filled to volume by rinsing the erlenmeyer flask and combining all the washings to fill the mark. A 5.0-mL aliquot of the CaCl2 solution was taken from the orignal solution and was transferred into an erlenmeyer flask with 10-mL NH3 buffer, 20-mL distilled water, and 5 gtts of EBT. The solution consumed 4.96 mL of an EDTA solution. MW: CaCO3 = 100.1 Compute for the N EDTA solution. 0.0053 N 0.0531 N 0.5313 N None of the choices
7-3: Analysis of a Ferrous Chloride Sample Titrations provide a method of quantitatively measuring the concentration of an unknown solution. This is done by delivering a titrant of known concentration into an analyte of known volume. (The concentration of an unknown titrant can also be determined by titration with an analyte of known concentration and volume.) In oxidation-reduction (redox) titrations, the voltage resulting from the mixture of an oxidant and reductant can be measured as the titration proceeds. The equivalence point of the titration, or the point where the analyte has been completely consumed by the titrant, is identified by the point where the voltage changes rapidly over a small volume of titrant delivered. In this assignment, you will determine the mass % of an unknown sample of ferrous chloride (FeCl2) by titrating it with a KMNO4 solution of known concentration. Start Virtual ChemLab, select Electrochemistry, and then select Analysis of a Ferrous Chloride Sample…
7-3: Analysis of a Ferrous Chloride Sample Titrations provide a method of quantitatively measuring the concentration of an unknown solution. This is done by delivering a titrant of known concentration into an analyte of known volume. (The concentration of an unknown titrant can also be determined by titration with an analyte of known concentration and volume.) In oxidation-reduction (redox) titrations, the voltage resulting from the mixture of an oxidant and reductant can be measured as the titration proceeds. The equivalence point of the titration, or the point where the analyte has been completely consumed by the titrant, is identified by the point where the voltage changes rapidly over a small volume of titrant delivered. In this assignment, you will determine the mass % of an unknown sample of ferrous chloride (FeCl2) by titrating it with a KMNO4 solution of known concentration. 1. Start Virtual ChemLab, select Electrochemistry, and then select Analysis of a Ferrous Chloride Sample…