The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. 0.75 in A C 50 kips 3 in 20 in 30 in

The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. 0.75 in A C 50 kips 3 in 20 in 30 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 45-mm-diameter solid steel shaft supports loads PA-1.2 KN and Pc-2.7 kN as shown. Assume that L₁ - 105 mm, L₂ = 205 mm, and 43-150 mm. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of (a) the maximum horizontal shear stress in the shaft. (b) the maximum tension bending stress in the shaft. L₂ C Pc Ly D
The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
A hollow bronze shaft of 75 mm outer diameter and 50 mminner diameter is slipped over a solid steel shaft 50 mm indiameter and of the same length as the hollow shaft. The twoshafts are then fastened rigidly at their ends. Find the maximumshearing stress developed in the bronze by end torque of 3 kN.mFor bronze G = 35 GPa and for steel G = 83 GPa.
The shaft consists of a 3-in.-diameter aluminum segment that is rigidly joined to a 2-in.-diameter steelsegment. The ends of the shaft are attached to rigid supports. Calculate the maximum torsion stressdeveloped in each segment when the torque T = 10 kip.in. is applied. Use G = 4 x 106 psi for aluminumand G = 12 x 106 psi for steel.
Q-1 A. solid circular shaft of (100 )mm diameter is transmit (120 )KW at r.p.m . Find the shear stress in the shaft B. the lap joint shown is fastend by three (20 )mm diameter rivets . Assumming that P-50 KN .Determine a. the shear stress in each rivets b. the bearing stress in each plate c.the max average tensile stress in each plate 25mm IAAI 25mm 5¢ 130 Soler
An 66 mm diameter alloy shaft is 6.5 m long and subjected to twisting. The shaft is attached to arigid support at the left end. Find the angle of twisting at the end of the bar and the maximumshear stress developed. Use G=81 GPa.
A 75mm shaft is subjected to 5KN-m torque. Find the stress developed in MPa. Meanwhile, determine the maximum mean diameter of a taper for use to fix a lever to a shaft. If it transmit a maximum torque f 750 in-lb . The shaft diameter is in 3in
The circular shaft made of 6061-T6 aluminum (E = 10 × 10³ksi, yielding strength ơy,ensite 37 ksi, oyear = 19 ksi) has a diameter of 0.6 in. If on a cross-section of the shaft, it is subjected to the internal resultant loads as shown, (a) calculate the stress components that act at point A due to each force/moment/torsion, (b) determine the combined state of stress at point A, (c) determine the combined state of stress at point B, (d) determine which point has the more (a) stress component at A severe stress state and calculate the principal stresses and maximum shear due to F, due to V, due to T, due stress at that point, and (e) calculate the safety factor based on the to My, due to Mz maximum normal stress yielding theory and (f) based on the maximum (b) at point A shear stress yielding theory. Ox = ,Jy = ,txy = (c) at point B Ty = ,02 = Txy = , Tmax v300 ( d) σ1- (e) S.F. = (f) S.F. = My-200 bin T-250 bin F500 b
A hollow shaft with an outside diameter of 149 mm and an inside diameter of 140 mm is subjected to both a torque of T-65 kN-m and an axial tension load of P-68 kN, as shown. Determine the normal and shear stresses at point Hand show them on a stress element. (1) Answers: MPa. MPa, Tay MPa, n, =
The rod shown below is of diamater 70 mm and is fixed at one end. It is subjected to 500 N.m and 300 N.m torsional moments as shown. Sketch the distribution of the internal torsional moment along the length of the rod. Also find the torsional shear stress at points A and B, and also the largest shear stress in the rod. Point B is to the left of the 500 N.m torsional moment and A is on the right of it. Round-up your answers to the nearest 1/100th of an MPa. y 35 mm 20 mm 500 N.m 35 mm- 300 N.m Torsional shear stress at A = MPа %3D Torsional shear stress at B = MPа Maximum shear stress = MPa %3D
The 12 kN.m torque is applied to the free end of the 5-m steel shaft. The angle of rotation of the shaft is to be limited to 3o. (a)Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use G = 83 GPa for steel.
A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further subjected to a torque of 10 kN-m. The maximum principal stress is ?