The cable spool shown at the right has a weight of 50 lbs and has a moment of inertia of .28 slug-ft^2. Assume the spool rolls without slipping when we apply a 50-lb tension in the cable. Find: friction force between the spool and the ground

The cable spool shown at the right has a weight of 50 lbs and has a moment of inertia of .28 slug-ft^2. Assume the spool rolls without slipping when we apply a 50-lb tension in the cable. Find: friction force between the spool and the ground

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.72P

See similar textbooks

Related questions

Q: A solid cylinder 5 meters in diameter and weighing 50 KN is at rest on a 45-degree inclined plane.…

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

Q: A weight of 500 kg is being lifted up at a uniform speed of 1.5 m/s by a winch driven by a motor…

A: Given data: M=500 kgV=1.5 m/sN=1000 rpmJo=Jw=0.3 kg.m2Tl=100 N.m Need to determine the motor torque…

Q: T Tolls without slipping on horizontal floor. For 23. For the system shown in figure, the disc of…

Q: A flywheel with a radius of gyration 0.9 m is fitted to a multi cylinder engine. It runs at 1000…

Q: ey shown below with radius of 140 mm and moment of inertia I Is from rest, find the distance it…

A: given:r=140mmI=7×10-3mass m=3Kg

Q: Question #1: Find the total system kinetic energy for the weight and pulley system shown in the…

Q: A caravan weighs 28 kN. It has a wheel base of 2 m, track width 1m and height of C.G. 300 mm above…

Q: A string holds and wraps around a solid cylinder (7-kg and R = 8-m). A person pulls the string…

Q: A post is held up by a rope that passes around a frictionless pulley and is attached to a mass M as…

Q: wo balls of mass ma and mp are connected by a massless rod of length L. The two vertical ashed lines…

Q: A thin rectangular plate of mass m and sides a by 2a rotates frictionless vector N. The axle is…

Q: agnitudes of 03 masses are gives as: m1 = 12 Kg, m3 = 7 Kg, m4 = 5 Kg. Find the value %3D %3D the…

Q: Problem: 1 The slider-crank shown in the figure is drawn to a certain scale. If actual length of…

Q: A boy who weighs 98lb is playing basketball on an outdoor basketball goal that uses weights set on…

A: Consider the weight of the boy as Wboy. As the basketball goal will tip at point A, so, find the…

Q: A vertical bar of length L with mass of 40 kg is rotated vertically about its one end at 40 rpm.…

Q: The centre of gravity for the ladder (mass = 10 kg) acts at point G as shown in the figure. Given…

Q: Answer all parts please Crate A has a mass, mA-5 kg and attached to a rolling ball with a mass of…

Q: |DG,| = 2|G,G,| %3D Ga ma L |DG,| = = Do mp Gp ° E T |AE| = |CD| = L L, m L, m А g = 9.81 m/s2 C

Q: The block M in Fig (a) weighs 500N and has a downward velocity of 5 m/s at the instant the force P-1…

Q: Find the angle of tilt θ with the horizontal so that the contact force at B will be equal to 0.26…

A: NB=.26NA angle of tilt θ FBD of smooth cylinder

Q: The drum shown in Fig. (a) has a radius of gyration of 30 cm and weights 1,8 kN. It is supported by…

A: Given data: k=30 cmw=1.8 kJW=1 kNr=37.5 cm Need to determine the angular acceleration of the drum.

Q: Consider a gymnast performing the "iron cross" as in Homework 1. Assume the gymnast's weight (W) is…

Q: QI: The cutter bar of a mower is connected to the P.T.O. shaft of a tractor making 1500 stroke per…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: A flywheel of moment of inertia 9.8kg m3 fluctuates by 30rpm for a fluctuation in energy of 1936…

A: Given data: N1-N2=30 rpmI=9.8 kg.m2E=1936 J Need to determine the mean speed of the flywheel.

Q: Q3/ A shaft has three eccentric of mass 1 kg cach. The central plane of the eccentrics is 50 mm…

Q: A uniform bar with mass M = 3.25 kilograms is shown in the diagram. hlo required to keep the

Q: 20. The moment of inertia of a flywheel is 0.54 kg-m? and it rotates at a speed of 3000 r.p.m. in a…

A: Given-Data:- Moment of Inertia = 0.54kg-m2 speed=3000rpm temperature=15oC water weight =2kg…

Q: What is the AVERAGE power input to the wheel during this time interval?

Q: Statical Stability. The scow shown in Fig. A above is 15 m long, 6 m wide, and 4 m deep. It has a…

Q: A horizontal beam of length 8 m is pinned at its left end so that it is free to rotate about that…

A: θ = 45o, L = 8 m

Q: A circular disc of uniform thickness of 20 mm, radius of 200 mm and mass of 20 kg, is used as a…

A: Given data Mass =20 kg Radius =200 mm N=600 rpm We have to determine kinetic energy of the flywheel

Q: 1. A uniform ladder of mass m and length is leaning at rest against a wall at an angle 0. The…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: A mass of 500 kg is being lifted at uniform speed of 1.5 m/s by a winch driven by a motor running at…

A: Write the given data:

Q: For the outlined sphere model of a water molecule consisting of two small spheres with the mass m= 3…

Q: A crane that is 10 meters long is rotating (while loaded), at 1 radians/sec. It is stopped instantly…

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: In the mechanism below, neglect the inertias of all the links and determine the cable tension force…

Q: Find the horizontal force , P required to turn the wheel weighing 500 over the block 10cm high if…

Q: A uniform plank is 5.00 m long and weighs 100 N. The cord that attaches to the plank 1.00 m from the…

A: From the above diagram We can say that the above system is in equilibrium and the net torque acting…

Q: Consider a wheel with four spokes as shown below. The radius of wheel is r = 0.18 m. The mass of the…

A: Draw the diagram of the given wheel and four spokes with their own center of mass. Write the…

Q: angular block of homogeneous density p and dimensions axbxcas shown Find the inertia lensor

A: The given rectangular block can be drawn as : The moment of Inertia matrix is given by IO…

Q: A solid cylinder 5 meters in diameter and weighing 50 KN is at rest on a 45-degree inclined plane.…

Q: The mass of a propeller is 4.5 tons and its centre of gravity is 3.5 mm from the centre of rotation.…

Q: Solve for the altitude if the given density is 0.371820226 kg/m³. Assume standard condition.

A: Given Data : Densityρ=0.371820226kgm3

Q: The compound pulley in Fig. P-1223 has a centroidal mass moment of inertia of 20 ft-ib-sec2. Find…

A: Let us draw the tension force ∑T=IαT1×1-T2×3=Iα ...(1) T1-3T2=20α

Q: Block String Rod Disk Mech 3. As shown above, a uniform disk is mounted to an axle and is free to…

A: Given data:

Q: Find the mean torque and the moment of inertia of the flywheel

A: Given: N=180 rpm Cs= 3% Angle (degrees) 0 60 180 180-360 Torque(Nm) 0 200 0 0 To determine:…

Q: A uniform disk of radius R and mass M is pivoted at point P and released at rest from the horizontal…

A: Radius of disk = R Mass of disk = M

Question

The cable spool shown at the right has a weight of 50 lbs and has a moment of inertia of .28 slug-ft^2. Assume the spool rolls without slipping when we apply a 50-lb tension in the cable.

Find: friction force between the spool and the ground.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
Find the horizontal force , P required to turn the wheel weighing 500 over the block 10cm high if radius of the wheel is 25 cm
Q3/ A shaft has three eccentric of mass 1 kg each. The central plane of the eccentrics is 50 mm apart. The distances of the centers from the axis of rotation are 20, 30 and 20 mm and their angular positions are 120 apart. If the shaft is balanced by adding two niasses at a radius of 70 mm and at a distance 100 mm from the central plane of the middle eccentric, find the amount of the masses and their angular positions.
The rope shown in the figure below is wound around a cylinder of mass 4.0 kg and I = 0.020 kg m2, about the cylinder axis. If the cylinder rolls without slipping, what is the linear acceleration of its center of mass? What is the frictional force? Use an axis along the cylinder axis for your computation. What happens if the frictional force between table and cylinder is negligible? Choose any axis for your computation.
Q3/ A shaft has three eccentric of mass 1 kg cach. The central plane of the eccentrics is 50 mm apart. The distances of the centers from the axis of rotation are 20, 30 and 20 mm and their angular positions are 120° apart. If the shaft is balanced by adding two masses at a radius of 70 mm and at a distance 100 mm from the central plane of the middle eccentric, find the amount of the masses and their angular positions.
3) A mannequin on skis with mass m must be mounted in a shop window. The manikin must be placed on a sloping plank with a static coefficient of friction μ. The center of the doll's is at a point with the distances a to the plank when the doll is standing vertically. Other dimensions can be seen in the figure. The shop wants the angle α to be increased until the skier slides down the plank but never rolls down or tips. What is the relationship between μ and dimension a for the boundary angle when the doll turns? In other words, what is the maximum allowed μ?
Consider a hollow clay cylinder, which has a moment of inertia 87 kg-m2. The cylinder is free to rotate frictionless-ly, and it starts from rest. It rotate about a fixed axis through its center. Let's assume that we apply a tangential force to the end of the cylinder (the flat face of the shape) with a magnitude which can range from F = 0 to F = 61 N. The force can be applied at any distance from the axis of the cylinder ranging from R=0 to R=4 m from the axis of rotation. (a) Find a pair of values of F and R that cause the disk to complete 2.00 rev in 10.0 s. (b) Is your answer for the previos part unique? How many answers exist?
A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?
The figure shows a bar in equilibrium position resting on the floor at point A and on the wall at point B. If the mass of the bar is m and the angle it makes with the floor is θ = π/6, find the magnitudes of the frictional and normal forces at points A and B.
Question 2: A prop shaft of a heavy-duty truck has two bearings which are positioned at 3 metres from each other. The shaft must rotate at 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of (MA = 10 kg) and (MB = 5 kg) acting at the extremities of the arms 0.45 m and 0.6 m long, respectively. The planes in which these masses rotate are 1.2 m and 2.4 m,
One end of a uniform 2.60m rod with a mass of 38.0kg is supported by a cable connecting one end to the wall so that the cable makes an angle of 42.0° with respect to the rod. The other end rests against the vertical wall, where it is held in place by friction so that the rod is perfectly horizontal. A sign with an unknown mass is hung from the rod 1.90m from the wall so that wall exerts a normal force of 1790N on the rod in the positive x-direction. What is the mass of the sign in kilograms?
Solve it correctly please. I will rate accordingly with 4votes. A 275-N solid sphere rests on a 35-degree inclined plane from thehorizontal. If the sphere has a diameter of 30 cm, calculate themagnitude of a horizontal force P passing through the center of thesphere and the reaction force of the inclined plane in order tomaintain the sphere at rest.