The beam in the figure below is subjected to a concentrated live load of 15 kN, a distributed dead load of 4 kN/m, and a distributed live load of 8 kN/m. 1- Sketch the influence line for the reaction at C. 2- Sketch the influence line for the shear just to the left of C. 3- Sketch the influence line for the moment at A. 4- Find the maximum positive moment at A due to the applied loads. 5- Find the maximum negative moment at A due to the applied loads.

The beam in the figure below is subjected to a concentrated live load of 15 kN, a distributed dead load of 4 kN/m, and a distributed live load of 8 kN/m. 1- Sketch the influence line for the reaction at C. 2- Sketch the influence line for the shear just to the left of C. 3- Sketch the influence line for the moment at A. 4- Find the maximum positive moment at A due to the applied loads. 5- Find the maximum negative moment at A due to the applied loads.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam (ABC) has a pin support at the left-hand edge (point A) and is supported by a thinner beam (CD). Beam ABC is loaded with a linearly increasing distributed load between point A and point B. The intensity of the distributed load is zero at point A and equal to at point B. A concentrated moment, Mc, is applied to beam ABC at point C. As the connection at point C is considered pinned, there is no transfer of bending moments between beam ABC and beam CD. Beam CD is pinned at one end (Point D) and connected to beam ABC via a pin (point C). There is a concentrated load, P, applied to beam CD a shown below. A Wo TD P = woL ↑ B -L/2 Figure 1: Two beam arrangement for question 1. L/2 Mc = woL² In order to analyse this structure, you will: a) Construct the free body diagrams for the structure shown above. When constructing your FBD's you must make section cuts at point B and point C. You can represent the structure as three separate beams. Following this, construct the axial force, bending…
1. Draw the influence line for the forces in bars CG, HD and EF of the truss shown in Figure 1. Hence, calculate the maximum forces in each bar due to a series of concentrated loads shown in the same figure, given also that the self-weight of the truss is 15kN/m. E F H D с 8x2m 40KN 70KN HI- 2m 3m 70KN 3m 60KN M B JI-SA
A beam (ABC) has a pin support at the left-hand edge (point A) and is supported by a thinner beam (CD). Beam ABC is loaded with a linearly increasing distributed load between point A and point B. The intensity of the distributed load is zero at point A and equal to at point B. A concentrated moment, Mc, is applied to beam ABC at point C. As the connection at point C is considered pinned, there is no transfer of bending moments between beam ABC and beam CD. Beam CD is pinned at one end (Point D) and connected to beam ABC via a pin (point C). There is a concentrated load, P, applied to beam CD a shown below. Wo |B Symbol E Fallow Tallow 000 L D P = wol ↑ L/4 L -L/2→ Figure 1: Two beam arrangement for question 1. Mc = wol² In order to analyse this structure, you will: a) Construct the free body diagrams for the structure shown above. When constructing your FBD's you must make section cuts at point B and point C. You can represent the structure as three separate beams. Following this,…
A statically determinate beam girder ABCD is overhanging at end is supported by pinned joined at A and roller at C respectively as shown in Figure 2. The beam girder is subjected to a series of concentrated moving loads across the whole beam girder of 7 m span. a) static equilibrium equation, draw the influence line for the reaction at A and C as well as shear force and bending moment at B. Indicate all-important values.
Q1. Figure Ql(a) shows a beam has a pin connection at D. The beam has a self weight of 6 kN/m and subjected to the live loads as shown in the Figure Q1(b). a) Draw influence line diagrams for the following functions i) Reaction at A ii) Reaction at C iii) Shear force at B iv) Shear force at C v) Moment at B vi) Moment at C All the important values of the influence line must be stated in the diagrams. b) Determine: i) Maximum reaction at A ii) Maximum shear force at B iii) Maximum moment at B Pin A D E for 4 m 2 m 3 m 1 m (a) Direction of movement 10 kN/m 60 kN 40 kN 4 m 2 m (b)
The beam in Figure 1 is under a distributed live load of 2 kN/m and a single concentrated live load of 6 kN. A is a fixed support, B is an internal hinge, and C is a roller. Determine the following: a. Draw the influence lines for the vertical positive reaction at C (Cy) and the moment at A (MA). b. the maximum vertical positive reaction at C (Cy) for the given loads. c. the maximum negative moment at A (MA) for the given loads. A 3m B 3m Figure 1 C 3m D
A. Find the reaction at support (RA) B. Find the reaction at support C (Rc) C. Draw the shear force diagram D. Draw the bending moment diagram
Refer to the frame shown . a. Draw the influence line for the vertical reaction at A. b. Draw the influence line for the moment at D. c. Determine the length of a 8kN/m uniformly distributed load that will put column AC in tension.d. Draw the position of a 15kN concentrated load and 5 kN/m uniformly distributed load that will give the maximum compressive force to column AC. e. Draw the position of a 15kN concentrated load and 5 kN/m uniformly distributed load that will give the minimum compressive force to column AC.
Hi , please help me Determine the magnitude of the reactions on the beam at A and D. Neglect the thickness of the beam.
Figure Q2a shows a cantilever beam structure, which is fixed at A and roller supported at C. The beam has an internal hinge at B. Draw the influence line diagrams for the following functions: (CO2, PO2, C3) i) Vertical support reaction at C Bending Moment at A Shear force at B 3m B: 3m Figure Q2a C 2m D 5kN 10kN 10KN 1m 3m Figure Q2b
For the beam shown, determine the reaction at B.
The reaction at support A RAy . The reaction at support C RCy The bending moment at B . The bending moment at C The maximum absolute value of the shear force in the beam The distance from A to the point at which the bending moment is zero Draw the shear force and bending moment diagram for the beam