The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After applying the loads shown, determine: (1) The maximum normal stress developed in each rod. (2) The horizontal displacement of end C with respect to the fixed support at A. (3) Suppose that only rod BC is exposed to change in temperature, what would be the change that keeps point C in the original position. Use Est = 200GPa, x= 12(10)-6 600 mm 400 mm 50 KN 40 kN 50 kN B C

The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After applying the loads shown, determine: (1) The maximum normal stress developed in each rod. (2) The horizontal displacement of end C with respect to the fixed support at A. (3) Suppose that only rod BC is exposed to change in temperature, what would be the change that keeps point C in the original position. Use Est = 200GPa, x= 12(10)-6 600 mm 400 mm 50 KN 40 kN 50 kN B C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The vertical force F applied at A is 50 kN. Compute the minimumdiameter of the steel wire, if the allowed elongation on steel wire4mm and its stress is limited to 250 MPa. Use Est = 200 GPa. Answer: d = ___________________
1. Problem 1: Segment AB of the bar is a hollow tube with an outer diameter of 1.5 inches and a wall thickness of 0.125 inch. Segment BC is a solid rod of diameter 0.75 inch. Determine the normal stress in segment AB in psi. 0.125 in. 0.75 in. 4800 lb 2800 lb 1.5 in. B C |A -6 in.- -6 in. Your answer 2. In Problem 1, determine the normal stress in segment BC in psi. Your answer
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. A) Determine the magnitude of load P. Express your answer in kips (rounded to the nearest hundredths.) B) Determine the shear stress on plane AB. Express your answer in ksi (rounded to the nearest tenths.)
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 185 MPa, determine the minimum diameter required for each rod. Assume P = 79 kN and Q = 134 kN. %3D dz di B Answers: d1 = mm. d2 = mm.
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e� = 55 mmmm and is subjected to the loading shown. Let a� = 200 mmmm , b� = 220 mmmm , c� = 350 mmmm , d� = 250 mmmm , and P� = 3.0 kNkN . Take point A to be at the top of the circular cross-section. As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, Mx��. b) Part B - Moment about the z axis at A Part C - Stress due to the normal force To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the normal force. Part D - Stress due to the bending moment about the x axis To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the bending moment about the x axis.
3. A composite bar consists of an aluminum section rigidly fastened between bronze section and steel section as shown. Axial load as applied at the position indicated. Determine the stress in each section. 20KN 40KN- 180KN 100KN 800 mm 2 1000mm 2 1200mm 2 Prepared By: DTM
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 1 and rod 2. Assume P = 80 kN and Q = 140 kN.
Bar (1) has a cross-sectional area of 0.75 in.2. If the stress in bar (1) must be limited to 39 ksi, determine the maximum load P that may be supported by the structure. D A 6 ft O 18.61 kips O 17.55 kips O 11.10 kips O 21.00 kips O 22.39 kips B (1) 4 ft C
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter required for rod 1. Assume P = 80 kN and Q = 140 kN. Express your answer in mm rounded to the nearest hundredths.
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to 32 ksi. Determine the maximum load P that may be applied to the connection. Clevis O 3.96 kips O 4.91 kips O 5.19 kips 3.44 kips O 6.79 kips
The rectangular bar has a width of w = 3.50 in. and a thickness of t = 1.50 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. Determine (a) the magnitude of load P. (b) the shear stress on plane AB. (c) the maximum normal and shear stresses in the block at any possible orientation. P Answers: (a) P= (b) Tnt = (c) Gmax Tmax = = i 31.5 Mi a B kips ksi ksi ksi