The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide.a) Determine the hydrostatic force acting on the gate.b) Determine the location of the force measured from the hinge.c) Calculate the minimum value of P to hold the gate in place. The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide.a) Determine the hydrostatic force acting on the gate.b) Determine the location of the force measured from the hinge.c) Calculate the minimum value of P to hold the gate in place.AirO 40 kPaY1 =1m.Hingey2 =3m

Answered: Image /qna-images/answer/c74190f1-56d0-461f-aee4-058137598c81.jpg

The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide. a) Determine the hydrostatic force acting on the gate. b) Determine the location of the force measured from the hinge. c) Calculate the minimum value of P to hold the gate in place. Air O 40 kPa Y1 =1m. Hinge y2 =3m

The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide. a) Determine the hydrostatic force acting on the gate. b) Determine the location of the force measured from the hinge. c) Calculate the minimum value of P to hold the gate in place. Air O 40 kPa Y1 =1m. Hinge y2 =3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force ( P) is required at point B for equilibrium. The weight of the gate is negligible, and C = 2 m J 5 m E = 1.2 m 9 = 60° %3D S.G. of Oil = 0.82 Oil, SG = 0 82 %3D Gate J
Q.1 -10° I- +20° 8m 26cm EI 5 cross seation 12. m Analyze the above structure for at=30° temperature difference using force methad, draw M diag ram. a=10-5 1/°C
solve for the total head loss given that the pressure drop between the junction=250kPa. (f=0.02) Use 3 decimal places
Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in. Segment BC is a solid rod of diameter d2. The average normal stresses must not exceed 3400 psi in rod AB and 6500 in rod BC, respectively. Use P1 = 3,650 lb. and P2 = 5,550 lb. a. Determine the smallest allowable value of d1 (in inches). Round-off to 2-decimal places. b. Determine the smallest allowable value of d2 (in inches). Round-off to 2-decimal places.
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine the total resultant force acting on the gate and the location of the center of pressure. +dy 3ft Unit weight of the liquid (y) Value of hbar (h) Area of the rectangular gate (A) Hydrostatic Force (F) Value of (Igx) Value of ybar (9) Location of the Hydro.Force measured from the water surface of the gate inclined (yp) Ib/ f ft ft lb fi ft ft ***answer Hydrostatic Force F on the box below:
D (5000 mm2) (4000 mm E (5000 mm) 3 m (4000 mm) A (S000 mm) B (5000 mm?) 100 kN 2 panels at 4 m = 8 m E = 200 GPa Determine the force in member AE in kN. If the force is compression, enter the answer as negative. („uu 000)
A line is recorded as 472.90 m long. It is measured with a 0.65 kg tape which is 30.005 m long at 20oC under a 50 N pull supported in both ends. During measurement, the temperature is 5oC and the tape is measured under a 75 N pull. The line is measured on 3% grade. E = 200 GPa, cross sectional area of tape is 3 mm2 and the coefficient of linear expansion is 0.0000116 m/oC Compute the actual length of tape during measurement Compute the total error to be corrected for the inclined distance What is the horizontal distance?
1. A barrel in the form of a frustum of a cone with a radius of 3m at the bottom and 6m at the top. It is 5m high and is 4/5 full of oil (0.85). Determine the a. Total hydrostatic force acting on the wall of the barrel in kN and b. its line of action from the bottom c. tensile force at the top band d. the tensile force at the bottom band
The face of a vertical dam has the shape of an isosceles triangle of altitude 4 m with an upper base of 6 m submerged vertically in the water. Find the force exerted by the water on the dam when the upper base is parallel to and 3 m below the surface of the water. (p = wight per unit volume water) 4 3 A F = ( 14 y - y2) dy (149 B F = P 3y - y) () dy (7y-y2) dy 4 3y (14 - 29 ) (2) dy 4 D 3 L (7 0 3 3 = F = P 0 0 0
Q1 . . A beam cross-section is subjected to an axial force P. Determine the application point of the load on the cross-section when the neutral axis passes through the points A and B as shown. Calculate P if the allowable normal stress is oallow 280 MPa. 15 cm 3 cm A 12 cm 3 сm Neutral axis B 3 cm
SECTION: 300 mm 10 KN m 800 mm A B 15m P= 300 KN e= 250 mm A. Calculate the stress at the top located in the centerline of the beam. (MPa) Calculate the stress at the bottom located in the centerline of the beam. (MPa) В.
2. Find the maximum value of P that can be exerted on the two pistons so that the tangential stress in the cylilnder does not exceed 4 MPa. Each of the piston has an internal diameter of 80mm and wall thickness of 2mm. P 42mm co'ce P