The 540-lb beam is supported at A and B when it is subjected to a force of P = 1000 lb as shown. (Figure 1) B 8 ft +2 ft -- Part A If the pin support at A suddenly fails, determine the beam's initial angular acceleration. For the calculation, assume that the beam is a slender rod so that its thickness can be ne Express your answer to three significant figures and include the appropriate units. HA Value Units a= Part B Determine the force of the roller support on the beam. Express your answer to three significant figures and include the appropriate units. HẢ ? By = Value Units

The 540-lb beam is supported at A and B when it is subjected to a force of P = 1000 lb as shown. (Figure 1) B 8 ft +2 ft -- Part A If the pin support at A suddenly fails, determine the beam's initial angular acceleration. For the calculation, assume that the beam is a slender rod so that its thickness can be ne Express your answer to three significant figures and include the appropriate units. HA Value Units a= Part B Determine the force of the roller support on the beam. Express your answer to three significant figures and include the appropriate units. HẢ ? By = Value Units

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.2P: Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the...

See similar textbooks

Similar questions

QUESTION: It is wanted to withdraw from A end with V_A velocity velocity (a_A = 0 m / s ^ 2) as shown on AB rod. Find the force F that will satisfy this condition. In this case, what are the support reactions at A and B points? Ignore the mass and atalat moments (I) and friction forces of the wheels. The inertia moment table of the rod is given.
The 490-lb beam is supported at A and B when it is subjected to a force of P= 1000 lb as shown. (Eigure 1) Figure B. 8 ft +2 ft
Q1: In the below drawings, three unbalanced masses and related details are provided. Please answer the following questions. a) a balancing mass is to be located at rp = 50 mm, then what would be the balancing m1 m1 650 mm 200 mm m2 mass (m,) and its angular position (Op) (Please use the r2 m2 A graphical method) r3 m3 15 m3 b) If the system is not balanced what would be the reaction forces at A and B. (FA, FB=?) n = 150 rpm r; = 30 mm m, = 1 kg r2 = 20 mm 40 тm 13= m, =3 kg m; = 2 kg k = please choose an appropriate scaling factor yourself SHOT ON MI 6 MI DUAL CAMERA
The iillustration depicts a prototype design for the High-G Rover. It is made up of an arm that is attached to a shaft that is pinned to a disk. The aarm has a retractable shaft that extends and contracts to cause the disk to rotate. To make the computation easier, let us assumee that the arm does nott rotate A. If the arm's total length is L = 640mm, the distance from the centre of the disk to the shaft pin is r = 112mm, and the arm rotates clockwise at a constant angular velocity of 250.273 rpm. 1.) Would an increase in angular velocity increase point C's linear velocity relative to point A? If so, why or why not? a.) What is the linear velocity of point C with respect to point A if the angular position of the pin (between AB and BC) is 0.578 radians? b.) What is the distance between points A and C if the angular position of the pin (between AB and BC) is 0.578 radians? c.) What is the linear velocity of point C with respect to point A if the angular velocity is increased by 34.34…
The 500-1b beam is supported at A and B when it is subjected to a force of P = 900 lb as shown. (Figure 1) Figure P 8 ft B 2 ft 1 of 1 If the pin support at A suddenly fails, determine the beam's initial angular acceleration. For the calculation, assume that the beam is a slender rod so that its thickness can be neglected. Express your answer to three significant figures and include the appropriate units. α= Submit Part B μA By= Value Request Answer μA Units Determine the force of the roller support on the beam. Express your answer to three significant figures and include the appropriate units. Value *** Units ? Review ?
3. Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass of 50 g. If 0 is 15° and the angular acceleration is 20 rad/s? M 3 m W Figure 3
In the graph the force versus displacement of a spring is given (the spring is shown in a separate figure--see below). The x-axis range is ±2 cm. The y-axis range is tFs, where Fs = 220 N. How much work does the spring do on the block (the mass "m") when the block moves from x₁ = 7.6 cm to 4.3 cm? W J y F. X -1.5 -0.5 0 10.5 1 1.5 -F How much work does the spring do on the block (the mass "m") when the block moves from x; = 7.6 cm to -7.6 cm? W = Question Help: Read Submit Question m
also find ax and ay The rod is supported by smooth journal bearings at A.B. and C and is subjected to the two forces Fi= 400 N and F 520 N (Egure 1) Figure 0.6m 0.6m 0.6m 0.4m 1 of 1 Part A Determine the 2 and y components of reaction at Cusing scalar notation Express your answers in newtons to three significant figures separated by a comma View Available Hint(s) [95] ΑΣΦ. 11 | vec C.C. Submit Part B ? B. B N Determine the az and a components of reaction at B using scalar notation Express your answers in newtons to three significant figures separated by a comma View Available Hint(s) ΑΣΦ | 19 | voc) N
A S S Q2. The double pulleys are fastened together to form a rigid unit. If V₁ = 9 and VB = 3 compute the angular velocity of the double pulley and the velocity of the load L. Use vector method. Also draw velocity-vector diagram of either pulley. Explain each step. Any illogical step will not be accepted. Refer to the following figure. UB B 600 mm- 400 mm L 1114
OP •C h W The man in the diagram is trying to move a large box by pushing on it with a force, P. The box weighs 300 N and its centre of gravity is located in the centre of the box (point C). Given: a = 1.8 m b = 0.8 m h= 0.9 m What is the minimum force that will cause the box to tip? Please include the unit ("N") within your answer and round to 3 significant figures (e.g. if the calculated answer was 55.562 Newtons please input: 55.6 N). Answer: What is the minimum coefficient of static friction that will permit tipping to occur? Please do not include the unit s (as there are none) within your answer and round to 3 significant figures (e.g. if the calculated answer was 55.562 please input: 55.6). Answer:
Turning moment 1mm = 60 Nm: crank angle, 1 mm = 1° . The turning moment shows the maximum energy that needs to be stored by the flywheel in the unit area is 2850 m² . The flywheel rotates at an average speed of 220 rpm with a total speed change of 2.5%. If the mass of the flywheel is 500 kg, find the appropriate dimensions (inner diameter, outer diameter and thickness) of the flywheel. Given that inner diameter of the flywheel is 0.9 outer diameter and the density is 7.2 Mg/m³ .
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 820 lb is applied to the tire at point C at an angle of 0 = 22° as shown. Assume the connection of the wheel to member AB is rigid. hs hy hi F BY NC SA W4. W, Ws 2013 Michael Swanbom Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value hi 10 in Wi 8.8 in h2 15.6 in W2 5.6 in h3 18.1 in W3 10.8 in h4 10.9 in WĄ 7.4 in h5 4.9 in W5 9.3 in For all answers, take x as positive to the right and y as positive upward. At point B, member AB exerts a force of B = j lbs on member BHE. At point A, member AD exerts a force of A + j lbs on member AB. At point H, shock GH exerts a force of H = i + i lbs on member ВНЕ. At point E, the magnitude of the force exerted on the car body by member BHE is lbs. At point D, the magnitude of the force exerted on the car body by member AD is lbs. At point G, the…