The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength pMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' 28 MPa and fy = 413.70 MPa. 750 mm 175 mm 100d mm 9-36 mm diameter bars 350 mm

The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength pMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' 28 MPa and fy = 413.70 MPa. 750 mm 175 mm 100d mm 9-36 mm diameter bars 350 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Referenced concrete When designing the same bim Why is the load in the case of moment greater than the load in the case of shear?
The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength oMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' = 28 MPa and fy = 413.70 MPa. 750 mm T175 mm 1000 mm 9-36 mm dibmeter bars 350 mm dooo
Given a beam section b angle D = 450mm * 950mm M*=1500kNm, f_{c}' = 32MPa f_{5y} = 500MPa and the maximum aggregate size=20mm. Design and detail the section. Use N28 bars for the main reinforcement and R10 bars for stirrups. Exposure classifi-cation A2 applies. Please don't hand writing
concrete design ACI code solve please
A 450 diameter concrete spiral column is to be desigmed to support a factored axial load of 3200 kN. Clear bar covering is 40 mm and the aggregate size is 25 mm. Use the 2010 NSCP with fc= 28 MPa, fy = 415 MPa, fyt = 415 MPa. Limit the gross steel percentage to 2%. Find the following a) The mumber of pcs of 28 mm diameter bars for the longitudinal reinforcements. b) The spacing of the 10 mm diameter spiral reinforcements in mm. c) Which of the following mostly nearly gives the clear spacing of the main longitudinal reinforcements in mm.
(2) * 28" 2#8 7 14" I2.5" NWC fé=3000 psi > 2 #10 z 2 #11 I 3" Grade 60 steel &Mn = ?
A 6” CHB was tested for quality and acceptance standard. The material failed with a load of 18,800kgf. Determine the compressive strength in MPA, PSI, Kips.
'bd . As per IS 456:2000 for M20 grade concrete and plain barsin tension the design bond stress t= 1.2 MPa Further, IS 456:2000 permits this design bond stress value to be increased by 60% for HSD bars. The stress in the HSDreinforcing steel barsin tension, a MPa. Find the required development length, La for HSD barsin terms of the bar diameter, = 360 S o.
Question 2A composite bar is made up of a steel strip 2 mm thick and 12 mm wide, sandwichedbetween two aluminium strips each 3 mm thick and 12 mm wide. The three strips areheld together by two rivets of 5 mm diameter each.2.1 Make a neat detailed sketch of the assembly.2.2 If the three strips are fastened together at 15 0C, determine the shear stress set up inthe rivets when the temperature is raised to 21 0C.Note: The resistance of a rivet in double shear may be taken as 1.75 times the resistancein single shear.(For steel: E = 200 GPa and α = 11×10 -6/ 0C)(For aluminium: E = 70 GPa and α = 22×10-6/0C)
(1) 3#8 4#10 15" I2.5" 24:5" 3" Grade 60 steel. fé= 4000 psi, NWC. & Mn = ?
Given the concrete (f c=6000 psi) I-beam shown in Figure 1 for the given loading: -draw the shear & moment diagrams -determine Vmax & Mmax -using ASD (Allowable Stress Design) method, check to see if the given loading produces stresses within the given allowable range (check both Omax & Vmax) Using ACI 318-99, allowable stresses are -for flexure, f = .45f'c -for shear, v. = 1.1√f. (HINTS: 8² -note that the beam is symmetric about both axes -Ix for a triangle is (1/36)bh³+Ad² ) 30 kips 16' 10 kip/ft 22' 20 kips 3'-4' -1-6 -1'-6" Figure 1 1'-
Please give me the correct solution and answer of this problem in principles of reinforce/presstressed concrete