The 13.9-in. spring is compressed to a 8.9-in. length, where it is released from rest and accelerates the sliding block A. The acceleration has an initial value of 370 ft/sec² and then decreases linearly with the x-movement of the block, reaching zero when the spring regains its original 13.9-in.length. Calculate the time t for the block to go (a) 2.5 in. and (b) 5.0 in. 8.9 -13.9" wwwwwww

The 13.9-in. spring is compressed to a 8.9-in. length, where it is released from rest and accelerates the sliding block A. The acceleration has an initial value of 370 ft/sec² and then decreases linearly with the x-movement of the block, reaching zero when the spring regains its original 13.9-in.length. Calculate the time t for the block to go (a) 2.5 in. and (b) 5.0 in. 8.9 -13.9" wwwwwww

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A block with a mass of 2.0kg is on a horizontal surface of negligible friction. The block is attached to one end of an ideal spring. The other end of the spring is attached to a vertical wall as shown. The block is pulled back and released from rest. The graph shows the horizontal position x of the block as a function of time t as the block oscillates on the surface. The block is moving to the right when it breaks away from the spring moving with its maximum linear speed. The block reaches an area with a rough surface that has a coefficient of kinetic friction of 0.200. Calculate the distance the block moves on the rough surface as it comes to rest. If he block is then replaced with a cylinder of radius 0.25 m and mass 2.0 kg, which is attached to the spring along an axis through its center. The cylinder is placed on a new surface, which allows it to roll while in oscillation. The cylinder is pulled back until the spring is stretched the same distance as in the previous experiment,…
Bodies A and B shown in the figure are connected to each other by two ropes. Body b is located on the frictionless surface. Acismi moves down from the stop position at T=0 with a constant acceleration of 100 mm/sec2. t = 2 sec how many mm do Bodies A and B move, respectively? в A Please select one: a.200 mm down, 50 mm right b.200 mm down, 200 mm right c.200 mm down, 800 mm right d. None of them e.200 mm down, 400 mm right
Learning Goal: In 1687, Isaac Newton presented three basic laws that describe the motion of a particle: • First law: A particle originally at rest, or moving in a straight line with a constant velocity, will remain in this state provided that the particle is not subjected to an unbalanced force. Second law: A particle acted upon by an unbalanced force, F experiences an acceleration, a, that has the same direction as the force and a magnitude that is directly proportional to the force. Figure 1 1 1 V 1 of 2
Motor M draws in the cable with an acceleration of 4 ft/s?, measured relative to the 200 lb mine car.(Figure 1) Determine the acceleration of the car. Neglect the mass of the pulleys. Express your answer with the appropriate units. Value ft/s acar = Determine the tension in the cable. Express your answer with the appropriate units. HA T = Value lb ape =4 ft/s?
n engineer is designing a spring to be placed at the bottom of an elevator shaft. If the elevator cable breaks when the elevator is at a height H above the top of the spring, calculate the value that the spring constant k should have so that passengers undergo an acceleration of no more than 9.0g when brought to rest. Let N be the total mass of the elevator and passengers. Spring constant k that the spring should have so that passengers undergo an acceleration of no more that 9.0g
4. A car starts from rest and accelerates uniformly to a speed of 72 km/h. over a distance of 500 m. Calculate the acceleration and the time taken to attain the speed. If a further acceleration raises the speed to 90 km/h in 10 seconds, find this acceleration and the further distance moved. The brakes are now applied to bring the car to rest under uniform retardation in 5 seconds. Find the distance travelled during braking.
23-A truck of mass 5 tonnes was moving with a velocity of 110 km/hr. The brakes were applied to bring the truck to 25 km/hr in 7.5 seconds . Determine the uniform force exerted by the brakes. Also find the velocity it will reach if the same force is applied in the same direction for 750 m and also find the time taken. The uniform force exerted by the brakes in N is The velocity it will reach if the same force is applied in the same direction for 750 m in m/s is The time taken if the same force is applied in the same direction in seconds is
If the mass of the vehicle is 1200kg, the total tractive effort 2800N and the force due to rolling friction is 2500N: what is the accelerating force of the vehicle? What will be the velocity at t= 300 sec is the vehicle starts from rest?
ASAP
KOREK a "la KOREK + HW2 SOLUTION: Write the kinematic relationships for the dependent motions and accelerations of the blocks. • Write the equations of motion for the blocks and pulley. 300 kg B Combine the kinematic relationships with the equations of motion to solve for the The two blocks shown start accelerations and cord tension. from rest. The horizontal plane and the pulley are frictionless, and the pulley is assumed to be of negligible mass. Determine the acceleration of each block and the tension in the cord. 12 12
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft.
It is known that the static frictional force between block B and the plate will be overcome and the block will slide when its acceleration reaches 3 m / s2 (Figure 7b_4). If the plate starts from rest at t = 0 s and accelerates uniformly at a rate of 4 rad / s2 , determine the time t and the angular speed of the plate when the block starts to slip (r = 200 mm).