Task 1 The Data: - Clearance volume of 70 cm3, the bore of cylinder is 130 mm, the stroke of compressor is 70 mm, the measured low and high pressures are 120 and 700 kPa, respectively, the volume before and after compression are 900 and 250 cm3, respectively. 1. Determine the volumetric efficiency of a reciprocating compressor 2. Calculate the isothermal and polytropic work of a reciprocating compressor 3. Evaluate the isothermal efficiency

Task 1 The Data: - Clearance volume of 70 cm3, the bore of cylinder is 130 mm, the stroke of compressor is 70 mm, the measured low and high pressures are 120 and 700 kPa, respectively, the volume before and after compression are 900 and 250 cm3, respectively. 1. Determine the volumetric efficiency of a reciprocating compressor 2. Calculate the isothermal and polytropic work of a reciprocating compressor 3. Evaluate the isothermal efficiency

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.16.| For a centrifugal compressor rotating at 2500 rpm, find the compression ratio for the following specifications. T = 300 K; nst (volumetric flow rate) = 1.25 m/s and t (the thickness of the flow section at the = 0.85; r, = 0.55; ra = 0.015; B, 60°, exit) =0.15 m.
Q2 An automotive engine has a bore of 90 mm; the stroke is 110 mm; and the length of the connecting rod is 166 mm Knowing that the volume of the combustion chamber is 75 cm³ and the intake valve closes 18° crank angle degree after BDC. If injection Started 10 degrees before TDC and ends 40 degree after TDC. And the engine is running at 3000 rpm. a. Calculate the geometrical compression ratio and the actual compression ratio? b. Find the ratio between the maximum speed of the piston to the mean piston speed for this engine? c. Find the injection period
Q4: Why the stroke length of the racing cars' engines is always smaller than its bore diameter?
A single acting, twin cylinder, Ammonia compressor with bore equal to stroke is driven by an engine at 250 rpm. The machine is installed in a chilling plant to produce 700 kW of refrigeration at -18°C evaporating temperature. At this temperature the cooling effect per kg mass is 1160 kJ. The specific volume of vapor entering the compressor is 0.592 m³ per kilogram. Assume 85% volumetric efficiency, determine the bore in mm.
A single – stage air compressor has a cylinder bore of 0.1m, a stroke of 0.075m and a clearance factor of 0.05. The conditions within the cylinder during suction which are identical to those of the environment are 0.1 Mpa and 300K . The compression and expansion index is 1.3. Calculate; a) The mass delivery rate b) The power required c) The volumetric efficiency d) The isothermal efficiency
A four-cylinder, 2.4-liter engine operates on a four-stroke cycle at 3200 rpm. The compression ratio is 9.4:1, the connecting rod r = 18cm, and the bore and stroke are related as S = 1.06B Calculate: (1) Clearance volume of one cylinder in cm³, L, and in3 (2) Bore and stroke in cm and in (3) Average piston speed in m/sec and ft/sec (4) Volume in the combustion chamber when crank angle at 90 degrees
3.11) The conditions of air at the entry of an axial compressor stage are: Рi %3D 768 тт Hg & Ti = 314 K. The air angles are B1 = 51°, B2 = 9°, a1 = az = 7°. The mean diameter 50 ст. The peripheral speed 100 m/s. Mass-flow rate 25 kg/s work done factor 0.95 mechanical efficiency 92 % stage efficiency 88 % (a) Air angle at the stator entry, [a2 50.18°] (b) Blade height at entry and the hub-tip diameter ratio, [h, = 19 cm ; dn/d = 0.449] (c) Stage loading coefficient. [V = 0.754] (d) Stage pressure ratio. [Po3/Po1 1.075] (e) The power required to drive the stage. [Power = 204.75 kW]
Air with negligible velocity enters the impeller eye of a centrifugal compressor at 15 deg C and 1 bar. The impeller tip diameter is 0.45 m and rotates at 18,000 rpm. Find the pressure and temperature of the air at the compressor outlet. Neglect losses and assume y = 1.4. A. 5.434 bar, 467 K B. 6.434 bar, 567 K C. 7.434 bar, 6467 K D. 8.434 bar, 767 K
5.9 From the data given below, calculate the power required to drive the compressor and stage air angles for an axial flow compressor. Stagnation temperature at the inlet: Overall pressure ratio: Isentropic efficiency of the compressor: 0.88 Mean blade speed: Axial velocity: Degree of reaction: 288 K 4 170 m/s 120 m/s 0.5 (639.4 kW, B, = 77.8°, ß2 = – 72.69°)
Q3: Turbomachinery The air mass flow rate in a compressor is 2 kg/s. The rotational speed is 10,000 rpm, with the inlet stagnation temperature and pressure of 293 K and 1.05 kPa, respectively. The number of rotor blades (Z) is 21 and the blade tip radius (r2) is 0.1m. Assume it is an axial inlet and radial exit impeller. Using the above data, determine: the specific work, We.
3.21) An axial flow compressor has an overall pressure ratio of 4.0 and mass flow of 3 kg/s. If the polytropic efficiency is 0.88 and the stagnation temperature rise per stage must not exceed 25 K, calculate the number of stages required and the pressure ratio of the first stage. Assume equal temperature rise in all stages. If the absolute velocity approaching the 1st stage rotor is 165 m/s at an angle of 20° from the axial direction, the work done factor is 0.83, the velocity diagram is symmetrical, and the mean diameter of the 1st stage rotor is 18 cm, calculate the rotational speed and the length of the 1st stage rotor blade at inlet to the stage. Ambient conditions are 1.01 bar and 288 K. [7,1.273, 356 rev/s, 19.45 cm]
A reciprocating piston compressor has the following:-Piston diameter of 300mm,-Stroke of 450mm,-Intake pressure of 1 bar,-Intake temperature of air at 200C,-Clearance volume of 3%,-Rotational speed N = 250rev/min,-Discharge pressure = 40 bar,-Compression and Re-expansion are polytropic process with k = 1.25a) Find the compressor’s characteristics (V,P T at all points A,B, C, D).b) Calculate the work and power of the compressor.