H.W.Given below the data of stage and discharge for acertain channel. Find the extension of rating curve forthese data, using Logarithmic and Least squaremethods with two cases :1. a=02. а#0Note :Use (In) instead of (log).Stage (m)Discharge (m³ /s)6 7 9| 1012 15 17204580180 254405720920Hayder H. Alwan

Given:- Stage in m discharge To find:- extension of rating curve a=0 a≠0

Answered: tain channel. Find the extension of…

Engineering

Civil Engineering

tain channel. Find the extension of rating ese data, using Logarithmic and Leas ethods with two cases: a=0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 12.3 For a dry sand specimen in a direct shear test box, the following are given: Size of specimen:…

Q: In the context of fiber reinforcement, what is a mat?

A: Fibre-reinforced polymer (FRP):- It is a composite material made of a polymer matrix reinforced…

Q: Determine the MAXIMUM SHEAR and MAXIMUM MOMENTS for using SHEAR AND MOMENT DIAGRAMS OR BY ANALYTICAL…

Q: Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to…

A: Given : Result of sieve analysis of a sample of aggregate. Required : According to ASTM C 33, the…

Q: The area in cut of two level cross-sections 35 m. apart are 34 sq. m. and 56 sq. m. respectively.…

A: Given Data: The area in cut of two level cross-sections, A1 = 34 sq.m. A2 = 56 sq.m. D = 35 m The…

Q: A Problem #6: P W (KN/m) L b B

Q: The beam is built up of 1/4-in vertical plywood strips separated by wood blocks. Determine the…

A: The given figure is shown below:

Q: Q1: A cruciform consists of two sections. The thickness of the black section is t, and the thickness…

Q: Torsional moment of resistance, T of the

A: Given, Closed thin walled tube has thickness=t Mean closed area within the boundary of the…

Q: .A rectangular open channel has a width of 5m and a bed slope of 0.001. For a uniform flow of depth…

Q: 2000 lb A 20¹ Determine the internal force on: B 1000 lb D Member AB positive (+) if Tension and…

Q: For the figure shown, let a = 200 mm and b = 75 mm. 0/26/2 y → a/2a/2 √x Compute the moment of…

Q: A rectangular beam 350 mm wide and effective depth of 500 mm is to be designed as subjected to an…

A: GIVEN : A rectangular beam 350 mm wide and effective depth of 500 mm is to be designed as subjected…

Q: Determine the tension developed in wire CD required for equilibrium of the 30 lb cylinder E and the…

Q: A W 150x24 (A=3060 mm², I₂ = 13.4x106 mm4, I = 1.83x106 mm²) steel column is 8 m long and is fixed…

A: Given :

Q: AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is…

A: Given values: Steel column using W 14*43 section having given properties. Length, L = 10 ft fy = 50…

Q: Concrete is required for a column that will be Severe exposed to freezing and thawing. The cross…

Q: From reservoir A water is supplied by a pipe that is 12 inches in diameter and 1000 ft long. At…

Q: Concrete is required for walls of a building that will be Severe Exposed to freezing and thawing.…

A: Reference : ACI 311 Mix design All tables are referred from ACI 311 Mix design. Table : Relationship…

Q: 1- What is the objective of standard consistency test? Explain how the consistency of cement paste…

Q: smallest force P required to raise the block A.

Q: Determine the moments of inertia of the shaded area shown with respect to the x and y-axes. Given a…

Q: Two identical plates of 63 mm wide and 3 mm thick is connected by a square pin with side dimension…

Q: Q-3 A vertical load W is applied to the rigid frame ABC shown in Fig.3. Use Castigliano's theorem to…

Q: NOTE: COMPLETE SOLUTION. SHOW ALL OF THE FREE BODY DIAGRAMS USED. Determine the maximum shear and…

A: The given problem has a simply supported beam with a loading arrangement as shown in the figure we…

Q: 8 kN/m 4 m B -2 m- 12 kN 125 mm 25 mm 25 mm 75 mm; 75 mm

Q: 6. The infinite sand slope shown in the figure is one the verge of sliding failure. The ground water…

Q: solution for an intersection. c Explain the factors involed in transport

A: b) Traffic signals or roundabouts arr generally considered for major arterial road intersections…

Q: For the built-up shape shown in the figure, determine the elastic section modulus about the…

A: Given data in question Dimensions To find out Section modulus

Q: Part A Determine the magnitude of the resultant force. Express your answer to two significant…

A: Given :

Q: Which of the following statements is true?

A: The design parameters of setting tank includes loading rate of solids, overflow rate, side water…

Q: value of maximum shear stress is?

A: Given data, A solid circular shaft, Diameter,d= 60 mm Transmit a torque,T= 1800 NmFind the value of…

Q: The 13-mm thick plates of the lap joint shown is made of A36 steel whose yield strength and tensile…

A: Solution: Given: t= 13-mm A36 steel yield strength = 248 MPa tensile strength = 400 MPa A325 grade…

Q: A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's…

Q: A bar of 6-mm in diameter is only allowed to decrease at a maximum of 3.96% of its total length.…

Q: From the figure below.assuming the support at A, B and C are rollers. 1.4 1.0 0.5 A Which of the…

A: Given data in question Beam Span member length To find out ILD reaction co ordinate NOte We will…

Q: . What is the modulus of elasticity of the material in GPa?

Q: Prob-2 A hydraulic power system consists of a dam with an inlet connected to a turbine. H=15m,…

A: Given : Head , H = 15 m Flowrate, Q = 1 m3/s HeadLoss, HL = 0

Q: 2. Determine the shear and moment in the floor girder as a function of x. Draw the shear and moment…

A: Given data FN = 55 MN = 62 SN = 71

Q: 4- List and explain methods of manufacturing of ready mixed concrete.

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: A stream of traffic moving at a speed of 40km/h and a concentration of 20veh/km is stopped for…

A: Note: As per guidelines policy, I have answered 1st 3 sub-parts only.If you need remaining…

Q: Determine the MAXIMUM SHEAR and MAXIMUM MOMENTS for using SHEAR AND MOMENT DIAGRAMS OR BY ANALYTICAL…

Q: Bolted and Riveted Connections 1. From the bolted connection shown, the diameter of bolts is 18mm0…

A: Solution: Given: db = 18 mm dbo = 18+3 = 21 mm Section: 100 x 75 x 8 mm Ag = 1340 mm2 t = 9 mm A36…

Q: Problem 2. Given are the following coordinates of stations of a simple curve: Station Northings…

A: Let T1 be the tangent between PC & PI, and T2 be the tangent between PI & PT.

Q: A rectangular timber beam is cut out of a cylindrical log of diameter D. The depth of the strongest…

Q: 2 Refer to Figure 10.43. A strip load of q = 1450 lb/ft² is applied over a width with B = 48 ft.…

Q: The car's braking distance from a velocity of v= 96 km/hr is 45 m on a level pavement. Assuming that…

Q: The maximum slump height for class seal concrete is _____. a. 2 inches b. 6 inches c. 8 inches d. 4…

A: Typical slump for ordinary decorative concrete applications would be in the 4- to 5-inch range The…

Q: The 79-lb force P is applied to the 200-lb crate, which is stationary before the force is applied.…

Q: Determine the forces in members BC and CG.1

Concept explainers

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.

Question

H.W.
Given below the data of stage and discharge for a
certain channel. Find the extension of rating curve for
these data, using Logarithmic and Least square
methods with two cases :
1. a=0
2. а#0
Note :Use (In) instead of (log).
Stage (m)
Discharge (m³ /s)
6 7 9
| 10
12 15 17
20
45
80
180 254
405
720
920
Hayder H. Alwan

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

Step 2 Solution:-

Step 3 Solution:-

Step 4 Answer:-

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 5 1 pts A pipe system has a discharge of 0.0316 m3/s with n = 0.013. Find the total loss of head between A and F. in m Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3 Pipe Length (m) Dia (mme) AB 180 150 BC 60 150 BE 150 150
8 The following data are obtained from the current meter gauging of a stream, at a gauging sta- tion. Compute the stream discharge. Distance from one Depth of water, d Immersion of current meter below water surface end of water surface (m) (m) depth (m) rev 0 0 1.0 0.6 10 2.2 0.44 36 1.76 20 6 4.0 0.80 40 3.20 30 8 8.0 1.6 46 6.4 33 10 4.2 0.84 33 3.36 29 12 2.5 0.50 34 2.00 29 14 1.2 0.72 16 16 0 Rating equation of current meter: v = 0.2 N + 0.04, where N = rev./sec, v = ANO 2 4 sec 40 48 50 57 53 59 57 51 49 52 53 48 velocity (m/sec).
SITUATION. The total head lost from A to E in the pipe system shown in the figure above is 15m. Assume f = 0.02 for all pipes. Useful properties are given in the following table. %3D 3 4 PIPE LENGTH (m) DIAMETER (mm) 450 600 600 500 3 360 500 4. 480 450 540 600 Calculate the discharge in pipe 3, in m^3/s. O 0.32 O 0.13 0.29 0.49 PI2m 5
A discharge of 600 liters/sec flows through a pipe having a diameter of 400 mm., length of 40 m. long. Compute the head loss of the pipeline using Mannings Equation with n = 0.013. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3
4. What is the ground water travel time from well MW1 to well MW2 (days) according to the following figure's condition? (Hint: Solve by Darcy's Law) - TOC stands for Top of Casing, and is an elevation with respect to a common datum DTW stands for Depth to water, which is the distance from the TOC to the water table MW1 MWI MW2 L = K= 900 ft TOC (ft) 18 ft/day 0.24 1052.6 1045.3 DTW (ft) 12.5 14.2 MW2
Q1/ Compute the Ground level of the points for the following readings: #~~~~∞ 1 3 2 А 5 4 с 6 8 7 F 9 1 0 11 Points 1 - 2 ABCDE-CH - ========== G Dis. (m) K 0 20 40 60 80 100 120 140 160 J 180 200 B.S I.S F.S Rise Fall 1.45 1.65 2.55 2.15 1.13 1.02 1.74 1.61 1.77 1.47 1.52 ==== 0.29 0.13 G.Elev. (m) 250 Remarks B.M Start point CL JJJJJJJJJ === CL CL CL CL End point CL ====
2. A water tank is fitted with a drain and outlet pipe as shown in the figure. The system has 82 feet of cast iron pipe of 1-½" diameter. Determine the flow rate through the pipe. All fittings are threaded and regular. f = 0.034 Kentrance = 0,5 Kreturn bend = 1.5 Ketbow = 1.4 Kytobe vatve = 10 Kexit = 1.0 15 ft. Fully open globe valve Kentrance Kethow Kesn Pond Ketum hend
Given a portion of a water supply pipe network system below. Determine the actual flow in each pipe and the respective head losses. Assume flow in pipes AB and BC in loop Il and I respectively equal to 0.142 m/s clockwise and 0.038 m/s clockwise for the first trial. Use Manning's Equation with n = 0.011. Length (m) 700 800 Diameter (cm) Pipes AB 30 BC 15 CD 1100 25 DE 650 35 EA 300 10 BD 1500 10 Qq = 0.15 m'ls QA = 0.10 m/s Qc = 0.10 m'/s Loop I Loop II E A Q = 0.15 m'/s
in a sprinkler irrigation system, the following information is given: the length of the sprinkler pipe is 360m, the pipe is made from Aluminum (C=100), where C is the Hazen -Williams roughness coefficient, sprinklers are spaced at 12 m*18 m (L*S), gross depth of irrigation (GDI) is 150 mm, the number of working hours at one location is 11 .hour, pipe slope is 0% Find Average pressure head -1 Pipe diameter -2
Q:- Prove that the angle of inclination of two fixed parallel plate as shown in fig, so that laminar flow at constant pressure occurs is 12#0) ya? 0= sin‘l( where:- Q:flow rate a:distance between plates fixed plates
Two reservoirs are connected by two pipes of the same length laid in parallel. The diameters of the pipes are 100 mm and 300 mm respectively. If the discharge through 100 mm diameter pipe is 0·01 m3 /s, what will be the discharge [ in m3/s] through 300 mm pipe? Assume that f is same for both pipes. a. 0.504 b. 0.181 c. 0.156 d. 0.952
Q#2: Compute the discharge of a river from the data given in table below. The current meter coefficients are; a = 0.04 and b = 0.76. Distance from bank (ft) Depth (ft) Meter Depth (ft) Revolutions Time (sec) 2 1 0.6 10 123 4 1.5 0.9 22 123 6 4 0.8 35 123 3.2 28 123 8 3 0.6 45 123 2.4 28 123 10 2 1.2 33 123 12 1 0.6 22 123