Suppose you are analyzing processing times for a machining operation. In your analysis, you found C, = 2.1 andCpk = 1.28. Given this information, which of the following sigma levels is the highest that you could claim yourprocess is capable of meeting?O 1 sigmaO 2 sigma3 sigmaO 4 sigma5 sigmaO 6 sigma

Explanation: With the given values of Cp and Cpk, the 4 sigma level, can be achieved for the…

Answered: Suppose you are analyzing processing…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Suppose you are analyzing processing times for a machining operation. In your analysis, you found Cp = 2.1 and Cpk = 1.5. Given this information, which of the following sigma levels is the highest that you could claim your process is capable of meeting? 2 sigma 3 sigma 4 sigma 5 sigma 6 sigma
In a manufacturing process, 10% of the produced units are defective. If the process produces 1000 units per hour, how many defective units are produced in a day (8 hours of operation)?
Sam's Long Life 75-watt light bulbs are designed to have a life of 1,150 hours with tolerances of +205 hours. The process that makes light bulbs has a mean of 1,040 hours, with a standard deviation of 55 hours. Compute the process capability ratio and the process capability index, and comment on the overall capability of the process. (Round answers to 2 decimal places, e.g. 2.75.) Process capability ratio 1355 Process capability index 945 1.24 .057 shorter lived While Cp = bulbs will be generated. indicates the process саpable, Cpk D indicates that
A manufacturer is selling pharmaceuticals that have a weight specification 199.8 to 200.2 mg, with a target value of 200 mg. Before sending its next shipment, the company collects a large sample of product and determines the mean weight of the sample is 199.89 mg, with a standard deviation of 0.035 mg. The process capability index for the current process is ____. Round to three decimal places.
Pepsi makes bottles that need to be between 30 and 32 oz. You do measurements, and you find that a normal distribution describes Pepsi's actual bottling machine performance. Specifically, the mean of the process is 30.5 oz, and the process standard deviation is 0.02 oz. If Pepsi wants to be within the tolerances 99.7% of the time, what is the process capability index? Round your answer to the nearest 2nd decimal point. For example, if your answer is 0.4435, enter 0.44 into the box.
Based on the 6-Sigma methodology, what is the corresponding DPMO when the Sigma Quality Level is 4.5 and process mean shifts by 10? 1.96 DPMO 3.4 DPMO 32 DPMO 233 DPMO 66800 DPMO
Meena Chavan Corp.’s computer chip production process yields DRAM chips with an average life of 1,800hours and s = 100 hours. The tolerance upper and lowerspecification limits are 2,400 hours and 1,600 hours, respectively. Is this process capable of producing DRAM chips tospecification?
A soft drink bottling machine exhibits the following production behavior: Hour Production Defects (Xi - u) 2 8:00 1010 19 9:00 980 23 10:00 1036 24 11:00 980 17 12:00 995 18 13:00 1030 23 14:00 1040 25 15:00 1005 17 16:00 1010 21 17:00 990 18 Z(Xi - µ)² = Calculate the control limits, determine the control state and define if the process is capable of operating at a maximum effect percentage of 2%
A process generating attribute data has an estimated sigma capability = 3.3. Assuming the process mean is shifted +/- 1.5 sigma from the target value, what is the estimated dpmo? Estimated dpmo = ____.
The director of research and development is testing a new drug. She wants to know if there is evidence at the 0.05 level that the drug stays in the system for more than 399 minutes. For a sample of 81 patients, the mean time the drug stayed in the system was 401 minutes. Assume the standard deviation is known to be 21. Step 1 of 5: Enter the hypotheses: Step 2 of 5: Enter the value of the z test statistic. Round your answer to two decimal places. Step 3 of 5: Specify if the test is one-tailed or two-tailed. Step 4 of 5: Enter the decision rule. Step 5 of 5: Enter the conclusion.
Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: a) What is the value of x? = x= 156.76 mm (round your response to two decimal places). b) What is the value of R? R= mm (round your response to two decimal places). Day 1 2 3 4 5 Mean x (mm) 158.9 155.2 155.6 157.5 156.6 Range R (mm) 4.2 4.4 4.3 4.8 4.3
You are the Green Belt Industrial Engineer in charge of manufacturing process for batteries that have an average voltage output of 12 volts, with production assumed to be normally distributed. You have decided that if a sample of 21 batteries taken from production has a sample average of 11 and sample standard deviation of 1.23, then the production is declared out of control and the line is stopped What is the confidence that your decision is a proper one to take?

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS

Suppose you are analyzing processing times for a machining operation. In your analysis, you found Cp = 2.1 and Cpk = 1.28. Given this information, which of the following sigma levels is the highest that you could claim your process is capable of meeting?