SOLVE STEP BY STEP IN DIGITAL FORMAT XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 3. If you have a 440/220 v, 60 hz single-phase transformer with 140 turns in the low voltage winding, you want to calculate: a) the number of turns in the high voltage winding b) the effective area of the core assuming that the maximum flux density should not exceed 1.2 Wb/m².

SOLVE STEP BY STEP IN DIGITAL FORMAT XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 3. If you have a 440/220 v, 60 hz single-phase transformer with 140 turns in the low voltage winding, you want to calculate: a) the number of turns in the high voltage winding b) the effective area of the core assuming that the maximum flux density should not exceed 1.2 Wb/m².

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.3P: Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source...

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
An ideal transformer has no real or reactive power loss. (a) True (b) False
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
. A 400/230V, 50Hz, single phase transformer has 200 turns on high voltage side. Find turns ratio, transformation ratio, and number of turns on low voltage winding. Also find the flux developed in the core
A 3000/200V ,50hz. , single phase transformer has a cross sectional area of 150 cm2 for the core. If number of turns on the low voltage winding is 80, determine number of turns on the high voltage winding and maximum value of flux density in the core.
A) :) Name two types of Transformer equivalent circuit and then compare them. B) !. ) Explain why do we need a B-H curve when we solve a parallel magnetic circuit in which one of the fluxes is given. BI Ff E E E E
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
b) Calculate the transformer core area that is required to limit the core flux density to 1.75T, when using 1000 turns on the primary and the power supply source is 240V at 50HZ. Write your answer in cm?.
10 A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and the number of turns of the low voltage winding is N2=34. The high voltage winding is energized with V1= 10 kV rms line-to-line and V2= 400 V rms line-to-line has been taken from the low voltage winding. What is the connection of the low voltage winding if the high voltage winding is Y-connected? Εισαγάγετε την απάντησή σας
1) The maximum flux density in the core of a 3000/240-V, 50 Hz single-phase distribution transformer is 1.25 Tesla. If the voltage induced per turn is 8 volts, determine the cross-sectional of the core in cm² Subject: Electrical Apparatus and Devices