Situation 3: Three reservoirs A, B and C are connected respectively with pipes 1, 2 and 3 joining at a common junction P. Reservoir A is at elevation 80m, reservoir B at 70m and C is at 60m. Assume f=0.018 for all pipes. Pipe 1: L-5000 m, D- 300 mm Pipe 2: L=4000 m, D = 250 mm Pipe 3: L=3500 m EL 80m A El 70m Q1=0.045 CMS El. 60m Q 12. Determine the flow in pipe 2. 13. Determine the flow in pipe 3. 14. Determine the diameter of pipe 3.

Situation 3: Three reservoirs A, B and C are connected respectively with pipes 1, 2 and 3 joining at a common junction P. Reservoir A is at elevation 80m, reservoir B at 70m and C is at 60m. Assume f=0.018 for all pipes. Pipe 1: L-5000 m, D- 300 mm Pipe 2: L=4000 m, D = 250 mm Pipe 3: L=3500 m EL 80m A El 70m Q1=0.045 CMS El. 60m Q 12. Determine the flow in pipe 2. 13. Determine the flow in pipe 3. 14. Determine the diameter of pipe 3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION 2: Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Elev 80 ha hez Elev 70 B 4000 m- 250 mm f-0.018 he 3500 m f- 0.018 Elev 60 Pipe 1: L= 5000 m, D = 300 mm Pipe 2: L= 4000 m, D = 250 mm Pipe 3: L= 3500 m 5000 m - 300 mm f= 0.018
Q3/ The water levels in the two reservoirs A and B are 104.5 m and 100 m respectively above the datum. Pipe joins each to a common point D, where pressure is 98:1 kN/m”*2 gauge at above the joint point D and height is 83-5 m above datum. Another pipe connects D to another tank C. What will be the height of water level in C assuming the same value of ‘f’ for all pipes. Take friction co-efficient f = 0-0075. The diameters of the pipes AD, BD and CD are 300 mm, 450 mm, 600 mm respectively and their lengths are 240 m, 270 m, 300 m respectively. 100 m Your answer
Problem 7- 64 Determine the flow in each pipe in the figure shown and the elevation of reservoir Cif the inflow to reservoir A is 515 Lit/sec. El. ? C El. 90 m El, 90 m B D. 300m - 450 mm t=0.03 El. 80 m 600m - 600 mm f-0.025 300m- 450 mem f0.03 900m- 450 mm 8. 600m - 450 mm 0.03
Three reservoirs A, B and C are connected respectively with pipes 1, 2 and 3 joining at a common junction P. Reservoir A is at elevation 80m, reservoir B at 70m and C is at 60m. Assume f=0.018 for all pipes.
5. Determine the flow in each pipe in the 3 reservoirs shown. EL. 80m EL. 50m A 2000m-500mm f=0,025 EL. 10m 4000m-800mm F0.03 1800m-400mm 1=0.02
10. Determine the flow in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 lit/sec. El. 7 B. 90 m E. 90 m B. D. 300m-450 mm El. 80 m 600m-600 mm f 0.025 300m-450m f0.03 600m 450 mm
Determine the flow in each pipe in the network shown in Fig. N. Use the Manning equation with n = 0.011. WS. EL 30 m W.S EL 24 m (1) L= 1200 m B 4-900 m Ly- 1500 m (2) D,-30 cm D- 20 cm W.S. EL 15 m EL O 0,- 15 cm (3)
ELEV. - 75m A ELEV.- 40m B L=1700m 2 =1900m D= 400mm f-0.02 D= 500mm f=0.025 ELEV. = 15m L=3500m D- 800mm f= 0.03 A three reservoir problem shown in the figure with their corresponding length and diameter. Determine the discharge in all pipes. A Q1 - 0.327 m3/s, Q2 - 0.458 m3/s, Q3 - 0.785 m3/s B Q1 - 0.295 m3/s, Q2 - 0.413 m3/s, Q3 - 0.708 m3/s Q1 - 0.431 m3/s, Q2 - 0.295 m3/s, Q3 -0.726 m3/s D Q1 = 0.346 m3/s, Q2 = 0.402 m3/s, Q3 = 0.748 m3/s E) No answer among the choices Q1 = 0.286 m3/s, Q2 = 0.519 m3/s, Q3 = 0.805 m3/s
01(a) There are two reservoirs, A and B, with the water surface elevation in A 10 m higher than that in B. These are connected through two pipes in series with pipe 1 starting from A and pipe 2 ending in B. Lengths of both the pipes are 100 m, diameter of pipe 1 is 30 cm and diameter of pipe 2 is 25 cm. At the junction of these pipes, water is being withdrawn at the L v² D 2g rate of 0.02 m³/s. Friction loss in the pipes is given by h = f and the Darcy friction, f, entrance and at the junction, for both pipes is 0.02. Neglecting the head losses at the estimate the total water withdrawal from reservoir A.
For the 4-reservoir shown, if elev. P' = 86.95m, find the discharge at the 150mm diameter pipe. Assume f=0.02 for all pipes. El. 50m El. 90m 450 m - 200 mm 600 600 m mm P El. 75m 300 m - 200 mm 900 m 150 mm El. 30m Vl
For the piping system shown below, determine the flow distribution and the piezometric heads at the junction (j) using the Hardy -Cross Method of solution. Power = 20 Kw D= 0.2 m, D,= 0.15 m, D,= 0.15 m f= 0.021, f= 0.018, f, = 0.023 L1=160m L2%3D205m L3=D410 30 m B 2 15 m C 10 m A Pump 3.
Situation 1: For the pipe network shown, the flow of water from the reservoir A to the junction is 0.035 cu.m.per second. Pipe 1: L = 300 m, D 202.70 mm, f = 0.015 Pipe 4: L = 300 m, D = 381 mm, f 0.015 Pipe 5: L = 450 m, D 303.20 mm, f 0.015 %3D Pipe 2: L = 150 m, D 202.70 mm, f 0.015 Pipe 3: L 75 m, D 202.70 mm, f 0.015 A B Q, = 0.035cumecs 4. Determine the flow in the upper branch Q2. 5. Determine the flow in the lower branch Q3. 6. Determine the flow in the lower branch Q4. 7. Determine the total head loss between the inlet A and the outlet B.