Digital Electronics I Question 4: Sensors are used to monitor the pressure and the temperature of a chemical solutionstored in a vat. The circuitry for each sensor produces a HIGH voltage when a specified maximumvalue is exceeded. An alarm requiring a LOW voltage input must be activated when either thepressure or the temperature is excessive. Design a circuit for this application with Truth Table.NOTE: YOU HAVE TWO PRESSURE SENSORS AND TWO TEMPERATURE SENSORS

Answered: Image /qna-images/answer/1f0bcf0f-4ccb-4327-bf30-4eccb1e5f326.jpg

Sensors are used to monitor the pressure and the temperature of a c at. The circuitry for each sensor produces a HIGH voltage when a spe eeded. An alarm requiring a LOW voltage input must be activated he temperature is excessive. Design a circuit for this application wi AVE TWO PRESSURE SENSORS AND TWO TEMPERATURE SENSORS

Sensors are used to monitor the pressure and the temperature of a c at. The circuitry for each sensor produces a HIGH voltage when a spe eeded. An alarm requiring a LOW voltage input must be activated he temperature is excessive. Design a circuit for this application wi AVE TWO PRESSURE SENSORS AND TWO TEMPERATURE SENSORS

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1.) a) PMMC meter has (10mA) half scale current deflection and (1500) internal resistance. Use this meter to design a dc multimeter of indirect ammeter and direct voltmeter methods to measure the following ranges of current and voltage: 50mA, 100mA, 1A, 5V, 50V, and 150V. Draw the circuit diagram of this multimeter with a control switch that can be used to measure either current or voltage.
What is the correct way to measure current in a completed circuit using a DMM? O Connected in series to the circuit being tested. O Connected in parallel to the circuit being tested. Connected across the load device in the circuit being tested. Connected in placed of the load device in the circuit being tested.
For what range of K values is the given system stable?
2. A. What parameters can be measured with a digital multimeter (DMM)? B. How does the DMM measure each parameter given that its internal circuitry actually only responds to voltage? C. What is the input resistance of the DMM on voltage ranges and why is this important? D. What voltage will the DMM read in the circuit below? Show computations. www DMM
A galvanometer with a internal resistance of 400 and a shunt resistor of value 'Rsh' is connected in series with a 100 resistor. A constant voltage VO' is applied aoross the oircuit, and the galvanometer deflects a certain amount. The shunt resistor is then removed, and replaced in series with the 100 resistor. With the same voltage 'VO', the galvanometer deflection is unchanged. Calculate the value 'Rsh' of the shunt resistor.
VII. QUESTIONS: 1. Which voltage source converts chemical energy to electrical energy? B. Battery D. Electronics Power supply A. Electrical Generator C. Solar Cell 2. Current is converted to voltage A. Through a voltmeter C. Through an ammeter B. Through a resistance D. Through a galvanometer 3. A voltage will not influence current only if the circuit is? A. Open C. Insulated B. High resistance D. Closed 4. Output of a digital multimeter is A. Mechanical C. Electrical B. Optical D. Analog 5. Write any two advantages using Analog multimeter over Digital multimeter. 1. 2.
7. How does the multimeter/voltmeter have to connect to the battery in order to provide an indication? What does this tell us about multimeter/voltmeter use and the nature of voltage? 8. Is there such a thing as voltage "at" a single point? 9. What would you say about a piece of wire if the ohmmeter needle didn't move at all when the probes were connected to opposite ends?
Analyze the scale divisions and determine the experimental error for the measurements, and enter it along with its units into table 5. Based on the value of the experimental error estimate the value of the "Volts" measurement Round your estimate to the correct number of significant figures, and enter this value into table 5. Below you are given the read-out from a voltmeter. Table 5 Volts Volts Error Value Value > Units > volts volts volts 4 6. 10
a) Explain how you make a change in the circuit to determine the operating point of the circuit shown in the figure.
Where is the best place in a circuit to find absolute zero when measuring voltage? O At the negative terminal of the battery. O At the positive terminal of the battery. O At either side of the circuit protection device. O On the ground side of the load device. ore
What is Energy Audit?Please explain about the energy audit and home energy audit?Give a introduction about it. *Explain for 2 page
2. Does ?a three digit color coding of resistor values? limit producible resistor value ranges? Why? If you need to increase these range what would be your solution??