Ruler of the "Porter" model, with the upper and lower arms of 178 mm each, fixed by a hinge 38 mm away from the center of rotation. The rotating balls have a mass of 1.15 kg each, and the axial weight affecting the bushing is 20 kg. The ruling commotion began =154. Elevation at 280rpm - The joints are at an angle of 30 to the vertical. Assuming that the force of friction is constant, find the minimum and maximum rotational speed when mg The angle of inclination of the arms to the vertical is 45 mgMg FG=154.Ruler of the "Porter" model, with the upper and lower arms of 178 mm each, fixed by a hinge38 mm away from the center of rotation. The rotating balls have a mass of 1.15 kgeach, and the axial weight affecting the bushing is 20 kg. The ruling commotion beganElevation at 280rpm - The joints are at an angle of 30 to the vertical.Assuming that the force of friction is constant, find the minimum and maximum rotational speed whenThe angle of inclination of the arms to the vertical is 45

GivenBP=BD=178mmPQ=38mmm=1.15kgM=20kgN=280rpmα=β=30o

Ruler of the "Porter" model, with the upper and lower arms of 178 mm each, fixed by a hinge 38 mm away from the center of rotation. The rotating balls have a mass of 1.15 kg each, and the axial weight affecting the bushing is 20 kg. The ruling commotion began =154. Elevation at 280rpm - The joints are at an angle of 30 to the vertical. Assuming that the force of friction is constant, find the minimum and maximum rotational speed when mg The angle of inclination of the arms to the vertical is 4

Ruler of the "Porter" model, with the upper and lower arms of 178 mm each, fixed by a hinge 38 mm away from the center of rotation. The rotating balls have a mass of 1.15 kg each, and the axial weight affecting the bushing is 20 kg. The ruling commotion began =154. Elevation at 280rpm - The joints are at an angle of 30 to the vertical. Assuming that the force of friction is constant, find the minimum and maximum rotational speed when mg The angle of inclination of the arms to the vertical is 4

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The arms of a Hartnell governor are of equal length. When the sleeve is in the mid- position, the masses rotate in a circle with a diameter of 150 mm (the arms are vertical in the mid-position). Neglecting friction, the equilibrium speed for this position is 360 rpm. Maximum variation of speed, taking friction into account, is to be 6% of the mid- position speed for a maximum sleeve movement of 30 mm. The sleeve mass is 5 kg and the friction at the sleeve is 35 N. Assuming that the power of the governor is sufficient to overcome the friction by 1% change of speed on each side of the mid-position, find (neglecting obliquity effect of arms), the (i) mass of each rotating ball (ii) spring stiffness (iii) initial compression of the spring
Clutch Mechanism 8. In the clutch mechanism shown, two flat circular disks of radius R are mounted so that they can be brought into contact causing a net frictional force. The contact pressure in general depends on the distance from the center and in one specific case may be modeled buy P(r) = Poe-kr, where k is a constant and r is the distance from the center of the discs. The integral cR F = 2m " P(r)rdr gives the total contact force between the discs. Cross-section a. In your own words explain where this formula comes from.
The ABCD structure illustrated on the left is used to stop the rotational movement of an inertia wheel attached in O while having a cusion B in contact with the wheel. The static friction coefficient is 0,4 and the cinetic friction coefficient is 0,3. The couple M applied on the inertia wheel is 300N*m. The lineic weight of the ABC membrane is 200N/m. The effort of compression in the hydraulic cylinder CD is 3,50 kN and its weight is negligible. Determine: 0.6 m a) if the inertia wheel turns or not b) the efforts on the ABC part 1 m 30° B 60 mm A M 0.3 m
B r P F A UBC Engineering Your team is prototyping a simple braking system for your model car. The 3.4 kg wheel with a radius of r = rad 0.15 m is rotating at w = 18 - .A servo motor can apply a variable force F, which in its first two seconds of operation is equal to F = 10t N and afterwards is equivalent to a constant force of F = 20 N . If the coefficient of kinetic friction between the braking arm and the wheel is μ= 0.2, determine the time needed for the wheel to come to a full stop. The point of contact P between the wheel and the arm is a distance r = -0.2 + 0.26 ĵ m from point A. The force of the servo motor is applied at exactly half of the horizontal distance to A from the point of contact. Assume the wheel can be treated as a disk and that the braking arm is massless. t =
ower shaft running at a steady speed of 175 rev/min driy 8 single-plate friction clutch of external and intern mm respectively. The masses on the countershaft have £ 250 mm and a total mass of 350 kg. The axial spring I 198 450 N, and 4 = 0-3. Assuming uniform acceleration guired to reach full speed from rest, and the work dissipad during that time. (U. Lond.) (Ans. : 99 g
The agricultural machine is powered by an electric motor through a flat beltsystem. The machine requires 6 flat belts and 40 kW power to operate at aspeed of 350 rpm. The pulley diameter of the machine is 650 mm and the pulleyof the electric motor is 330 mm. The centre distance between the pulleys is1100 mm. The belt speed is not to exceed 30 m/s. Calculate the tensions in thebelt.
Q9 / A Hartnell type governor with a central spring under compression has balls each of mass 2 kg. The ball and sleeve arms of the bell crank levers are respectively 100 mm and 60 mm long and are at right angles. In the lowest position of the governor sleeve, the radius of rotation of the balls is 80 mm and the ball arms are parallel to the govenor axis. Find the initial spring force in order that the sleeve may begin to lift at 300 rpm. If the stiffness of the spring is 30 kN / m, what is the equilibrium speed corresponding to a sleeve lift of 10 mm.
A flywheel absorbs 2500 ft-lb of energy at a coefficient of fluctuation of 0.10. The mean diameter of the flywheel is 72 inches. The weight of the arms and hub is 12 % of the rim weight. The mean rim speed is 80 fps. Consider the specific weight of the flywheel as γ = 0.26 lb/in3. A. Find the mean rpm of the rim. B. Determine the weight of the rim. C. What is the cross sectional area of the rim?
Q. A centrifugal clutch has 4 shoes which slide radially in a spider keyed to the driving shaft and make contact with the internal cylindrical surface of a rim keyed to the driven shaft. When the clutch is at rest, each shoe is pulled against a stop by a spring so as to leave a radial clearance of 5 mm between the shoe and the rim. The pull exerted by the spring is then 500 N. The mass centre of shoe is 160 mm from the axis of the clutch. If the internal diameter of the rim is. 400 mm, the mass of each shoe is 8 kg, the stiffness of each spring is 50 N/mm and the coefficient of friction between the shoe and the rim is 0.3. Find the power transmitted by the clutch at 500 r.p.m.
7The total sleeve movement in a Hartnell governor is 3 cm. The mass of rotating balls is 1.5 kg each. At the mid position of the sleeve arm, which is 6.5 cm long, is horizontal. The ball arm has a length of 7.5 cm. At the mid position of the sleeve, the balls rotate at a radius of 10.5 cm. Due to the mal adjustment of spring, the equilibrium speed of governor at top position is 415 rpm and In lowest position it is 430 rpm. Determine (1) Stiffness and initial compression of spring. (ii) Required initial compression in spring which gives equilibrium speed at the topmost position which is rpm more than the lowest position neglect bliquity.m = 1.5 kg
A min cage of mass 4t is to be raised with an acceleration of 1.5m/s2 by a cable passing over a hoist drum of 1.5m diameter. What is the power required when the load has reached a velocity of 6m/s, neglecting the inertia of the drum and weight of the cable, but allowing for bearing friction torque of 3kN at the drum? What is the power required at a uniform velocity of 6m/s
The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of 0.29 mm and 0.43 mm, respectively. The total mass of the pulley system is 14 kg and its turning radius is 0.26 mm from its center. The mass of block A is 9 kg and the mass of block B is 2 kg. If the coefficient of kinetic friction between block B and the floor is 0.2, find the angular acceleration of the pulley.