Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 7 mm in diameter. Assume a = 500 mm, b=250 mm, h = 400 mm, P = 950 N. and 9 = 55°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D (a) Orod = (b) Tpin B = (c) Tpin A = (1) a i i B b h MPa MPa MPa

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 7 mm in diameter. Assume a = 500 mm, b=250 mm, h = 400 mm, P = 950 N. and 9 = 55°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D (a) Orod = (b) Tpin B = (c) Tpin A = (1) a i i B b h MPa MPa MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thicknesses shown in the figure. The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to the rivets. How many 19-mm-diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE?
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 8 mm in diameter. Assume a = 675 mm, b = 350 mm, h = 475 mm, P = 725 N, and 0 = 60°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod = (b) Tpin B = (1) a i i Tpin A = i B b MPa MPa MPa h
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 8 mm in diameter. Assume a = 650 mm, b = 325 mm, h= 525 mm, P = 800 N, and 0= 65°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod = (b) Tpin B = (c) Tpin A = (1) a i i i B b MPa MPa MPa
3. The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to rivets. How many 19mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? -14-mm-thick gusset plate 6m - 13-mm-thick angle G. 4 m 4 m 4 m 4 m 96 kN 200 KN 96 kN PRE 6-mm-thick angle Pac
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 8 mm in diameter. Assume a = 575 mm, b = 250 mm, h = 450 mm, P = 750 N, and 0 = 55°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A Answers: (a) Orod (b) Tpin B = (c) Tpin A= (1) a i i i B b с h MPa MPa MPa
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 9 mm in diameter. Assume a = 550 mm, b = 300 mm, h = 450 mm, P = 900 N, and 0 = 60°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod = (b) Tpin B = (c) Tpin A = (1) tel tel a i i B MPa MPa MPa
Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working bearing stress due to rivets is 140 Mpa Thickness of the member is 5 mm Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 kN 120 kN B. 3 m E 200 kN 4 Panels @ 4 m = 16 m
Pins B and C experience the same force, and are both used in a double shear connection. Consider pin B. Use the ultimate shear strength, the factor of safety, and the force at B to calculate the minimum required diameter for pins B and C. dpin B,C= ? (unit mm)
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
Determine the magnitude of the pin force at A. Assume W - 620 Ib, a- 4.6 ft, b-3.1 ft,r-8 in. C B W Answer: A- Ib