Replace the two cable tensions which act on the pulley at O of the beam trolley by two parallel forces which act at pulley connections A and B. The forces are positive if up, negative if down.

Q: hat is Reynold’s equation of motion? Explain capillarity and pitot tube.

A: Reynolds' equation of motion is a fundamental equation in fluid mechanics that describes the…

Q: A Problem 4 L/2 Mo C B 000

A:

Q: Two questions in one, see pictures below  The assembly shown below with M8x1.25 bolt/nut is…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: If the supporting rods of equal diameter are made from A992 steel, determine the required diameter…

A: According to the given data E=29000 ksi for A992 steel σAllow=24 ksi   A free-body diagram at point…

Q: What is a machine cluster? What is the decision making criterion on basis it is decided whether the…

A: According to the question We need to find explain The machine cluster? The decision-making criterion…

Q: The diagram below illustrates a simplified version of the Jet Propulsion Laboratory's 25-ft space…

A: Given Data: q1=3181.0 W  Surface (1) and (2) are Flat Surface (4) can be Assumed as a perfect…

Q: A 1,000-N uniform boom at - 62.5" to the horizontal is supported by a cable at an angle of weight w=…

A: Given data is

Q: If the magnitudes of OA and OB are 10 mm and 20 mm, respectively, find (i) The vector form for…

A: The magnitude of OA is 10 mm. The magnitude of OB is 20 mm.

Q: Water at 80◦C flows steadily from a tank shown below at a volume flow rate of 475 L/min to a pump…

A: Given:Water temperature, T=80oCVolume flow rate of water, Q=475 L/min=475*10-360=0.0079167 m3/sPipe…

Q: The bar AB is pin-connected at one end to the slider at A and is pin-connected at the other end at…

A:

Q: A 25-lb sphere A is held at the 55° angle shown and released. It strikes the 13-lb sphere B. The…

A: The mass of sphere A is ma=25 lb. The mass of sphere B is mb=13 lb. The coefficient of restitution…

Q: A solar collector consists of a long duct through side consists of a glass cover of emissivity &₁ =…

A:

Q: Consider the area shown in (Figure 1). Suppose that a = 4.8 in., b = 9.6 in., and c = 3.2 in. Figure…

A:

Q: The mass of the suspended object is m = 60 kg.(Figure 1) Figure 0.6 m -0.8m 0.2 m -0.6m- 02 m m…

A:

Q: 5-91. The A992 steel shaft is made from two segments. AC has a diameter of 0.5 in. and CB has a…

A:

Q: Consider an artificial boundary layer flow past a flat plate. The profile of the velocity field…

A: Given data:- Velocity profile uU=yδ1.2 for 0<y<δ uU=1 for y≥δ To find:- the displacement…

Q: The movement of point P is constrained by the curved slot in OB and by the slotted bar OA. If…

A: Given-Information:- θ˙ =3t3/2θ = 15°t = 0 at θ = 0°r2 = 4 cos 2θm2 To-Determine:- a. Angular…

Q: Match the most appropriate form of the equation for the moment of inertia to the image shown. All…

A: Given: The distance is r. The mass is m. The radius of gyration is k. The distance of mass moment of…

Q: Recommend general considerations when selecting a site for Thermoelectric Power Plant.

A: This question is based on the consideration should be counted for a thermoelectric power plant.

Q: The simply supported beam shown in Fig. Q3 is subjected to a 75 kN point load and 40 kN/m…

A: F=75kNW=40 kN/m

Q: Problem 12.3 A truck is traveling down a long steady grade (0 = 15°) as shown in the figure. The…

A:

Q: The stresses shown on the right below act at a point on the surface of a cantilever beam, as shown…

A:

Q: A reversible heat pump absorbs heat at a temperature of 25.00oC and produces heat at 61.00oC, The…

A: Heat absorbed by heat pump at temperature, (TL)=25oC=298 K. The heat produced at the temperature,…

Q: A 1-in-diameter solid round bar has a groove 0.1-in deep with a 0.1-in radius machined into it. The…

A:

Q: Question No. 12: Methane CH4 is burned with stoichiometric amount of air during a combustion…

A: CH4+2O2+3.76N2→CO2+2H2O+7.52N2

Q: Determine the temperature, in °C, of Butane at 30 bar and a specific volume of 0.026 m³/kg. Hint -…

A: The pressure of butane P=30 bar The specific volume V=0.026 m3kg

Q: 18:(a) What are the approximate chemical composition of gasoline, LPG, diesel, natural gas &…

A: Thikness of copper plate = 2.5 cm  k = 355 W/m.K Thikness of asbestos = 3.2 mm k = 0.110 W/m.K…

Q: A pulley is mounted on a 1.5in diameter shaft. Rotation is driven by a cylindrical steel pin with an…

A: shaft diameter d=1.5" yield strength of the pin Sy=18000psi torque applied T=250lb-in factor of…

Q: As shown in figure P5 below, a shaft carrying a pulley that is keyed to the shaft. The shaft is 2.25…

A:

Q: What is the ideal mass flow rate for a refrigeration and cryogenic plant for oxygen production?

A: Ideal mass flow rate: Ideal mass flow rate is referred as the rate at which a fluid flow through a…

Q: A rigid massless rod is rotated about one end in a horizontal circle. There is a particle of mass m₁…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: Warm oil (s.g. 0.92) flows in a 2 in. or 50 mm smooth brass pipeline at a mean velocity of 8 ft/s or…

A: What is viscosity? It is the property which defines opposition of resistance between two adjacent…

Q: 1. What is wrought iron in gray? 2.  Why does gray cast iron lack tensile strength? 3. What can…

A: Wrought iron is the purest iron which contains 99.5% iron but may contain upto 99.9% iron.Wrought…

Q: The BEP for a pump operating at 1750 RPM with a 13-inch impeller is 1000 gpm, 150 ft. Using the pump…

A:

Q: You are molding plates of Alumina from powder. The customer continues to complain of the poor…

A: Change in particle size in first mill, ∆d1=250 μm-35 μm=215 μmFirst mill time, t1=8 hoursChange in…

Q: 3) What are the flow Q and the velocity V when total head loss is H = 25 m? KENTRANCE = 1.0 KGLOBE…

A:

Q: A gas furnace has an efficiency of 75%. How many BTU will it produce from 1000 BTU of natural gas.

A: Efficiency= 75%=0.75 Natural gas heat= 1000 BTU

Q: 1. Determine the equations of the elastic curve for the beam using the x; and x coordinates. El is…

A:

Q: Example 6.2. In Figure 2, a force of F = 250 N is applied to the end at B. Determine the speed of…

A: The force F=250 N

Q: Prob. # 2] The 1.5-in-diameter solid steel shaft shown below is simply supported at the ends. Two…

A: Given Data: Diameter of Shaft d = 1.5 in Diameter of Pulley B dB=4 in Diameter of Pulley C dC=8 in…

Q: 8. Block A of mass m is moving down along the vertical, curved, rough path (kinetic coefficient of…

A:

Q: Find the vector format of vector AB. V C 1 m 2 m A 0.75 m 40° 2 m 3 m B y

A: For a given system, we need to find the vector AB

Q: Q2: Steel tube having outer diameter of 80 mm is used to transmit 10 kW of power when turning at 50…

A: According to the given data Outer diameter D=80mm P=10kW N=50rpm Tallow=90MPa We need to find Inner…

Q: 6/16 A cleated conveyor belt transports solid homogeneous cylinders up a 15° incline. The diameter…

A:

Q: PROBLEM: A reheat cycle with two stages of reheating is executed with steam expanding initially from…

A: Solution: Given Data:   To Find:

Q: A certain natural gas has following volumetric analysis: 65 percent CH4, 8 percent H2, 18 percent…

A:

Q: A cleated conveyor belt transports solid homogeneous cylinders up a 17° incline. The diameter of…

A:

Q: The beam is subjected to the load shown. The beam is made of material having an E = 200 GPa and I =…

A:

Q: Use the diagram shown above. Given: • D₁ = 10 ft • D₂ = 3 ft . W 100 #/ft Solve for the internal…

A:

Q: Find the stream lines and path lines of the particles of the two dimensional velocity field…

A: