QuestionThe following fiqure shows the position# 9tigure shows thevs timeattoched' to the end of aplott of an 80massTheapring.theposition is geven in meters andtime in secands. The phasc angle is ?0.4(0.0.2427)0.2(0.7469, 0)(0.027.0)040.60.8t (s)-0.2( m)

Answered: Image /qna-images/answer/ed9ac74f-1042-474f-abcf-8f6da10b8c31.jpg

Answered: Question #9 The following figure shows…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

500 700 From the figure shown. -1875 To determine: C 1300 E 1300 a) Piston force BC b) Piston force FE c) Pin force G and J d) Pin force D and H 300 B 500 D 450 600 20 kN Draw the FBD: H 550 - all needed parts for calculation 250 Analytical solution. 3 digits behind comma. Dimensions in mm
52 What is the distance between the center of circle A and the corner at B? R3 03 Start a new drawing based on Mech-Millimeters.dwt. Draw the object shown in Figure A-1, starting with the center of the Ø3 circle at point 5,5. Draw only the object, not the dimensions and then answer the following questions: O 186794 198628 193132 171870 R1.0 TYP. 18 8 2 2 1 10
I want to know the exeac process of answering Sb,x. Is it Sb,x=Sb cosθ right? I'm confusing It's Sb,x=Sb sinθ or cosθ the solutions says both Sb,x & Sb,y is Sb cosθ but I think it can't be same. In this question, θ=45degree, so cosθ & sinθ is same but if the degree changes, it's different. Which one is right? Please answer me the Sb,x & Sb,y by showing it using sinθ & cosθ
Draw the three projections of the body in Figure 1- using AutoCAD 1-Do not write the dimensions on the drawing 2- Draw with the same measurements as shown 3 -Show graphics properties At least properties are required for the circle and arc R10 R20 40 35 55 -1- JSI 9.
Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 kN, just write 120 kN Do not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 rad/s^2, 100 kN) For stresses, type (C) for compression and (T) for tension one space after the unit. (ex: 18.19 MPa (C), 6.88 psi (T))
Question 27 3 7 9 -1 7 8 6 A = 1 9. -1 2 3 | -5 6. 4 -7 3 -2 -3 8. Solve for the determinant of A. Tommo
In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e angle a at which slider B reaches the extreme right position. Write your answer in degrees but do not write the unit. 7 cm. Find the value of 7777 x. Answer: DELL
Please show how to solve for #24. The answer is A, but I don't understand how to get there. I have solved for a perpendicular using a = v^2/r and substituting with v = 2 pi r / T. a perpendicular = 50.29 m/s^2, but I am not sure how to solve for a parallel using the equation (a parallel = r * angular acceleration.) Thanks! T = period r = radius a = acceleration
Solve the following.
do not reject . let other do the solution if u dont know. skip 86 30 ugh hole 16 6 20 Dig 28 18 Dia for the above isometric view , sketch the orthographic view in first angle proiection using catia v5 software. 36
9- O A) 3*F(AD)=(5.385)*F(AE) B) F(AC)=(5.385)*F(AB) C) 2*F(AD)=(5.385)*F(AC) O D) F(AE)=W O E) 4*F(AD)=(5.385)*F(AB)
Velocity. Suppose the distance travelled by a tanker ship departing from port is given implicitly by the equation 2-4st-75³-0 Where s is the distance in kilometres and it is time in seconds (s). Use implicit differentiation to calculate the velocity of the ship when s= 40 and 14 seconds. Note: Enter your solution as a decimal rounded to four (4) decimal places without units.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Question #9 The following figure shows the position vs time plot of an80gmass 3pring. The position is geven in meters and attoched to the end of a the time in secaads. The phasc angle is ? (0.02427) 0.2 (0.7469. 0) (0.027. 0) 04 0.6 0.8 t (s) -0.2 44 (w) x