Question 1: Select an S shape for the tension member shown in Figure (1). Themember shown will be connected between two plates 3/8 in thickness. Bearingtype connection use S.H. 7/8-in. bolt diameter, A325 of bolts, threads are notexcluded from shear planes. The service dead load is 50 kips, the service live loadis 150 kips, and the length is 22 ft, Neglect block shear. Use A36 steel and S12xw.Fig. (1)

Since the total design load (300 kips) is less than the nominal capacity (466.18 kips), the selected…

Answered: Question 1: Select an S shape for the…

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.11.10P

See similar textbooks

Similar questions

4. An UPE 300 is to be used as a tension member and it is bolted to a 10mm thick gusset plate with bearing type 8-M20 8.8 bolts as shown in the figure below. a. Check all spacing and edge distance requirements. b. Compute the allowable tensile strength of the channel UPE 300. Don't consider shear strength of the bolts and bearing strength of the bolt holes. [all dimensions are in mm] Material both for gusset plate and UPE 300: S275 F-275N/mm² Fu=430N/mm² UPE 300 Ag = 5660 mm² tw 9.5 mm x = 28.9 mm 70 160 70 + 10mm thick gusset plate +50+ 80 -80-80-50 o +50+80 -80 80-50 UPE 300
Check the bolted section of the given gusset plate connection assuming that the connection is done by M12 bolts with a staggered arrangement. The maximum design tensile axial force to be sustained is Ned = 168 kN. Assume a grade of S235 steel. P. Gusset plate BỘ do=13mm Gusset plate O DO t=16mm t-16mm1 Ni.Ed FO NtEd do=13mm do3D13mm G. 40mm 40mm 140 mm 240mm 30mm
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 1/2" thick Gusset Plate 3/8" thick 2" 3" 2" 2" 3" 3" 2"
A992 steel is used for the tension member shown. The bolts are ¾ inch in diameter. The connection is to a ⅜ inch thick gusset plate. A. Determine the nominal strength based on the gross area. B. Determine the nominal strength based on the effective net area.
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 2" 3" 2" 1/2" thick Gusset Plate O 2" 3" 3" 2" 3/8" thick P
The tension member shown in figure below is a PL ½ x 8 of A36 steel. The member is connected to a gusset plane with 1 ⅛ inch-diameter bolts. It is subjected to the dead and live loads shown. Does this member have enought strength? Assume that Ae=An. a. Use LRFD b. Use ASD
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for tension on gross area in kip? Express your answer in two decimal places. 1/2" thick Gusset Plate 3/8" thick 2" 3" 2" 2" 3" 3" 2" P.
The tension member shown is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. 2" 2" -|-|- |-|-|- -| 3 die einheitliche O O O OO O
The bolted connection shown is a bearing type connection. Which of the following best gives the shearing capacity, ØRn. of the bolts? Consider threads excluded from shear plane and deformation at bolt hole is a design consideration. Standard size holes. PL350x12mm = 250 MPa C250x22.8 70 114 M20 A490 70 40' 60' 60 '40 SECT. A d tw bf tf Mm 15.8 mm^2 mm mm mm mm C250x22.8 2880 254 6.1 65 11.1 Ix(10^6) Sx(10^3) ly(10^6) Sy(10^3) Zx(10^3) Zy(10^3) rx ry mm^4 mm^3 mm mm^4 mm^3 mm mm^3 mm^3 27.7 218 98.1 0.912 18.5 18.5 257 40.3 O 424.8 KN O 1,102.7 KN O 3,770.7 KN O 1,637.1 KN

Recommended textbooks for you

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning