Q4- Draw Mohr's circle for the case as seen in Fig. 4. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Show principal stresses on an appropriate sketch. 94 MPa 42 MPa 62 MPa

Q4- Draw Mohr's circle for the case as seen in Fig. 4. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Show principal stresses on an appropriate sketch. 94 MPa 42 MPa 62 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.25P: The stresses at a point on the down tube of a bicycle frame are trx= 4800 psi and t = -1950 psi (see...

See similar textbooks

Related questions

Q: 4. Mohrs Circle construction for generalized plane stress

A: Mohr's Circle of Generalized plane Stress.

Q: Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker…

Q: The state of plane stress at a point is represented on the element shown in the figure below. (a)…

Q: 4 ksi The state of plane stress at a point is shown on the element. (a) Draw Mohr's circle neatly to…

Q: as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane…

A: Given: The diameter of the shaft, d = 20 mm = 0.02 m

Q: 90 MPA 60 MPA 20 MPA

A: Given that, σx=-20 MPa,σy=90 MPa,τxy=60 MPa, Steps to draw mohr's circle: 1. Take direct stress at…

Q: Ql: For the Figure shown below, determine (a) the principal stresses and show them on a sketch of a…

Q: The hollow circular pipe is subjected to two forces P=1800 and F=2500. Inner and outer radius of the…

A: The data given in this question, Force, P=1800 N, and F=2500N The inner radius of the pipe, ri=24…

Q: In the figure, a force of 1 kN is applied by means of an arm connected to a shaft with a diameter of…

A: Now, calculate the torque due to 1 kN force, T = 100 x 1 kN = 100 kN-m Bending moment due to 1 kN, M…

Q: Find normal and shearing stresses at point A .

A: For the Normal Stress at pt.A (considering the maximum stress condition) Normal Stress, σx = PA…

Q: Problem 1-3 The Cartesian components of stresses at a point are given as belou : O = 7, 0y = 6, oz =…

A: The cartesian components of stresses at a position specified in the inquiry are known to us :…

Q: the stresses at point A.

A: To find Stresses at point A

Q: 3. An element in a strained body is subjected to a tensile stress of 100 MPa and a shear stress of…

A: When an amount of force act on an object, then the force has the tendency to change the shape of the…

Q: Find the minimum principal stress for the stress case given in the figure.

Q: The stress at a certain point is as shown in the figure. If the maximum in-plane shear stress…

Q: 1- The principal stresses or a point in the section of a member are 50 MPa or 20 MPa both tensile.…

A: To find : The normal and shear stress. Given : The principal stresses are σ1=50 MPa. σ2=20 MPa.…

Q: In the figure shown, determine the normal stresses at AD and BC shearing stress at bolt D bearing…

A: Given data, Diameter of the bolt, d = 16 mm Free body diagram of EDC where, RD and RC are the…

Q: 2. The hollow cylinder is fixed at the wall and pressurized at p = 2,000 Pa. Its outer diameter (OD)…

A: For the given cylinder the following are the reasons for creating stress at point A: compressive…

Q: Q4. The stresses at a point in a component are 160 MPa and 60 MPa both tensile. Find the intensities…

Q: 3. (a) Using Stress transformation equations, determine the principal planes, the principal…

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

Q: Assume the plane stress element shown in Fig. E3-a represents the stress a geosynthetic membrane…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as…

A: Given, Force, F=178NInside diameter, di=2.66cmOutside diameter,do=3.34cm Moment of Inertia,…

Q: Q1) A stat of stress is specified in Figure. By using Mohr's circle determine the normal and…

A: Given:σx=60 MPaσy=-18 MPaζxy=15 MPa

Q: Q2: For the stresses at the point shown, find: The maximum shearing stress. • The principal stresses…

A: To Find : the maximum shearing stress the principal stresses and planes Given : stress acting…

Q: A load of 7,000 N acts on the machine part shown in Fig. 5a. The machine par thickness of 15 mm…

Q: For the shown element, what are the principal stresses and their orientations (ew, cew), draw the…

A: (a) To find: The principle stress and the orientation of principle stress Given: The stress in…

Q: Q5: - Draw the Mohr's Circle of the stress element 6 MPa shown in figure. Find: - A 6 MPa The…

Q: Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as…

A: Given Data Force applied on the wrench and the force transferred to the end of the pipe, F=178 N…

Q: - The state of plane stress is represented by the stress element below. Draw the Mohr's circle,…

Q: In the figure shown, determine the normal stresses at AD and BC shearing stress at bolt D + ,…

A: Given, tEDC = 10 mmwEDC = 50 mmtAD = tBC = 8 mmwAD= wBC = 36 mmd = 16 mmF = 20 kNLAD = LBC = 0.2 m…

Q: Determine (a) the principal stresses and (b) the maximum shear stress and associated normal stress…

A: normal stress in x direction σx=300 MPanormal stress in y direction σy=-100 MPa (-ve for…

Q: The state of plane stress at a point is represented on the element shown in the figure below. (a)…

A: Given details: σx=16 MPa, σy=0, ζxy=-10MPa Formula for principal stress: σ12=σx+σy2±σx-σy22+ζxy2…

Q: Problem 2. Amaterial element in plane stress is subjected to stresses: = -5000 psi Ox Oy = -2000 psi…

Q: 934. If an element is subjected to the state of stress shown in Fig. P-934, find the principal…

Q: * The state of plane stress at a point is represented on the element shown in the figure. The…

A: GIven σx=10MPaσy=30Mpaτ=20MPa

Q: For the element shown below, determine: 1- The principal stresses and the maximum in-plane shear…

A: A perpendicular force applied on a body per unit area is referred to as stress. There are three…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Loads acting on a body induces stresses in all directions at any point of the body. The point can be…

Q: Take the micro-body from the self-loading member, and bear the stress on it as shown in Figure a.…

A: For the given stress element,…

Q: Question 3) Plane stress state ata point is given in the figure. L. a) Calculate the principal…

A: τxy=10 MPaσ1,2=σx+σy2±σx-σy22+τxy2 Since it is case of pure shear so σx=0 &…

Q: From the figure shown, the diameter of each segment is indicated. Determine the average normal…

Q: The state plane stress at a point is represented by the stress element below. Determine the stresses…

A: Find the state of stress at 30 degree clockwise oriented element.

Q: The stresses acting on element A in the web of a train rail are found to be 'X (MPa)' tension in the…

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 14MPA 24 10 20 MPa The stresses…

A: Given Normal stress at X axis = 20 MPa Normal stress at Y axis = 14 MPa Slope of plane = 24 and 10…

Q: At a point on the web of a girder on a gantry crane, the stresses acting on the x face of a stress…

A: Given dataσx = 6250psiσy = 3030psiζxy = 1425psiTo determine1) Draw the mors circle2) The principal…

Q: An element in plane stress is subjected to stresses o, = -60 MPa, oy = -40MPA, and Ty = 35MPA, as…

Q: 2.7. The principal stresses at a given point are o1 =10 MPa, ơ2=-100 MPa. Sketch Mohr's circle for…

A: Given data: The positive principal stress, σ1=10 MPa. The negative principal stress, σ2=-100 MPa.…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

100%

Strength of Materials

Q4- Draw Mohr's circle for the case as seen in Fig. 4. Determine the principal stresses and the
maximum in-plane shear stress acting at the point. Show principal stresses on an appropriate
sketch.
94 MPa
42 MPa
62 MPa
Fig. 4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
Assume that the normal strains x and y , for an clement in plane stress (see figure) are measured with strain gages. (a) Obtain a formula for the normal strain x in the : direction in terms x , y and Poisson’s ratio v. (b) Obtain a formula for the dilatation L’ in terms of x , y and Poisson’s ratio v.
-18 through 7.4-25 An clement in plane stress is subjected to stresses sx,,sy., andtxy(see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
The stresses at a point on the down tube of a bicycle frame are trx= 4800 psi and t = -1950 psi (see figure). It is known that one of the principal stresses equals 6375 psi in tension, (a) Determine the stress (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented clement.
Assume the plane stress element shown in Fig. E3-a represents the stress a geosynthetic membrane used in a mechanically stabilized earth wall. If the reference state of stress for this element results in the Mohr’s circle plot shown in Fig. E3-b, determine: The principal stresses. The principal directions (angles to the principal planes). The maximum in-plane shear stress. It is known that the seam, which is rotated 45 deg from the vertical as shown in Fig. E3-c, will fail if subjected to a tensile stress of 25 kPa or a shear stress of 1 kPa. Determine the normal stress and shear stress acting on the seam, and state if the seam will fail due to the loading indicated.
Construct a Mohr's circle for the following point stresses: ox = 60MPa, oy = 10MPa and Txy = +20MPa, and hence determine the stress components and planes in which the shear stress is a maximum.
Considering the original state of stress as shown in figure below and recalling the already developed equations for normal and shear stress at an angle Ɵ c.c.w from x-axis, mathematically prove that the planes of maximum in-plane shear stress are inclined at 45o to the principal planes.