Q2:A) An experimental text program is being set up to calibrate a new flow meter. The flow meter is to measure the mass flow rate of liquid flowing through a pipe. It is assume the mass flow rate (m) is a function of the pressure difference (AP)across the meter, diameter of the pipe (D), viscosity of the fluid (μ), and the density of the fluid (p). Using the dimensionless analysis, find the-groups for this case study.
Q: Use the method of compsite areas to calculate the centroidal coordinates of the plane regions shown…
A:
Q: Determine the vertical acceleration of the cylinder with a weight WA = 71 lb for each of the two…
A: Calculated the vertical acceleration of the cylinder with weight WA =71lb for each of the two cases.
Q: Q1-A- A man stands on the middle rung of a 250 N ladder resting on a smooth floor and against a wall…
A: Given that, Weight of ladder = 250 N Tension force in the string = 50 N Reaction at A = 1.3 kN =…
Q: What's the similarity, advantage and disadvantage between hydraulic system and pneumatic system?
A:
Q: Calculate the gas pressure, of air density is 1.22 Kg/m3, L-200 mm * Patm Gas at pressure p Tank…
A: Given:- L = 200 mm = 0.2 m Air density = 1.22 kg/m3 To Find:- Gas Pressure (P)
Q: vacuum refrigeration system consists of a large insulated flash chamber kept at low pressure by…
A: Assumptions made : 1) No heat tramsfer to the surroundings 2)pump work is neglegible 3)No effect…
Q: Show the derivation of the following Maxwell relations with complete solutions (F)-(23) Әр as as…
A: To Do :- Derive Maxwell's relations
Q: Describe with the help of a neat sketch the principles of operation of an internal expanding shoe.…
A:
Q: Question 2: a) What is entrance region and fully developed region? Discuss it with figures. b) What…
A: Given questions: a) What is entrance region and fully developed region? Discuss it with figures b)…
Q: Q3:B) A rectangular gate (length 3m, wide 1m) inclined at 50⁰ with the horizontal level and hinged…
A:
Q: an air-standard Diesel cycle has a compression ratio of 16 and a cutoff ratio of 2. At the beginning…
A: Compression ration, r=16Cutoff ratio, rc=2Pressure at the beginning of the commpression process,…
Q: Q5 The three cables are used to support the 30-kg flowerpot, as shown in the Figure 9. Determine the…
A: Given: M = 30 kg and three cables To find : force in each cables
Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…
A: given; is the knowledge of the size of structure necessary?
Q: A pair of gears, having 40 and 30 teeth respectively are of 25° involute form. The addendum length…
A: Given Data The number of teeth on the smaller gear is: T1=30 The number of teeth on the larger gear…
Q: Q2-B- Fill in the blank with the correct answer. 1. When the resultant of force system acting on a…
A:
Q: 5) For water P= 125 KPa, h= 2685.4 Kj/kg O Mixture O Saturated vapor O Saturated liquid Superheated…
A: For water at P = 125 kPa, Enthalpy = h = 2685.4 kJ/kg From the saturated water- Pressure table, we…
Q: The velocity of a fluid flowing in a pipe is to be measured by two different Pitot-type mercury…
A: we have to judge the use of these manometers in this experiment
Q: 17- What welded joints is the gap gauge used? (ISO 17637) a-for fillets weld joint b- for butt weld…
A:
Q: Consider the non-interacting tanks in the figure below. Resistances R 1 and R 2 are linear. The flow…
A: Given : To find : h
Q: Q2: The lecturer Aous used to drive his car early inorder to arrive and teach his students some…
A: The lecturer should start driving at 7 : 10 a.m. in order to travel from Baghdad to Tikrit…
Q: A propeller running at a revolution rate of 120 rpm is found to produce no thrust when its velocity…
A:
Q: Test results obtained on a NACA 23012 airfoil show the following data: aº C₁ 0 0.15 9 1.20 If this…
A: Given: at 0 deg , Cl = 0.15 at 9 deg, , Cl = 0.2 AR = 7
Q: 17- What welded joints is the gap gauge used? (ISO 17637) for fillets weld joint a- b- for butt weld…
A:
Q: Q2: The lecturer Aous used to drive his car early inorder to arrive and teach his students some…
A: The time that he should start driving from Baghdad: 7:10 a.m.
Q: Q/ 1000 kg car requires eight seconds to change its speed from 0 km/h to 140 km/h. What is the…
A:
Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…
A:
Q: Question 2: a) What is entrance region and fully developed region? Discuss it with figures. b) What…
A: Entrance Region: The entrance region is the portion of a pipe where fluid entering the pipe acquires…
Q: Determine the yield strength sy and the ultimate strength su of the A36 steel either from Materials…
A: To find: For A36 Steel Yield strength sy = ? Ultimate strength su = ?
Q: tand the Scotch Yoke Mechanism and observe and calculate the displacement of slotted slider from…
A: we have to discuss on the position analysis of scotch yoke mechanism
Q: The net head influence to a Caplan turbine is 45m. the working fluid hits the rotor and the rotor…
A:
Q: What is the distinction between Dirichlet and derivative boundary conditions?
A:
Q: In energy conversion in boiler, which combinations of the following are encountered as losses? a.…
A: Introduction: Boilers are used in power plants to generate high-pressure steam, which allows the…
Q: A Carnot engine has an efficiency 50% when its sink is at a temperature of 27°C. The temperature of…
A: As given in question, Efficiency of Carnot engine = η = 50% = 0.5 Sink temperature = T2 = 27 oC =…
Q: Determine the speed at which the basketball at A must be thrown at the angle of 30 degree so that it…
A: Given Angle = 30 To find The velocity of basketball from point A
Q: Determine the resultant moment of * the forces shown about point A 200 N 60 N 30% 30° TOON 0.75 m…
A:
Q: 16. Find the Relative C.O.P. of a refrigeration system if the work input is 60 KJ/kg and…
A: Given, Work input to the refrigerator = W = 60 kJ/kg Refrigeration effect produced = QL = 130 kJ/kg…
Q: What is entrance region and fully developed region? Discuss it with figures. What is differana
A: we have to discuss about entrance region and fully developed region
Q: Air flow though the device shown in figure. Select which set of the following conditions is TRUE…
A: Option : (e) is correct At point 1& 4 At point 1 cross section area of device is less as…
Q: 100N 160 150 mm 150 mm 400 N 30 60° 320 N
A:
Q: Q2:A) An experimental text program is being set up to calibrate a new flow meter. The flow meter is…
A:
Q: QUESTION 2. A smooth rod with a length of 21 is bent as in Figure 2 and small oscillations are made…
A:
Q: 1. Compute the maximum shearing stress and deflection of a helical spring made from bronze…
A: we have to determine the maximum shearing stress
Q: Q2: The lecturer Aous used to drive his car early inorder to arrive and teach his students some…
A: The time that he should start driving from Baghdad: 7 : 10 a.m.
Q: Determine the internal energy change for carbon monoxide, in kJ/kg, as it is heated from 312° K to…
A: Given:T1=312 KT2=1456 K
Q: A uniform bar of mass m is pivoted at point O and supported at the ends by two springs, as shown in…
A:
Q: Which device can be used to recover waste heat from flue gas? a. flue gas recoverer b. boiler…
A: Feed water economizer is the correct answer
Q: Question 1: Determine the mathematical model of the linear mechanical system shown below, given f(t)…
A:
Q: Q3: A small sphere, rolling with an initial velocity of 9 m/s, moving up a plane inclined 30° with…
A: Given: Let us consider the given figure and the data, Initial Velocity,vi=9 ms Final Velocity,vf=0…
Q: Q2-B- Fill in the blank with the correct answer. 1. When the resultant of force system acting on a…
A:
Q: 1- The use of lubricant in wire drawing die.
A: we have to discuss the use of lubricant in wire drawing
Step by step
Solved in 2 steps with 3 images
- A) An experimental text program is being set up to calibrate a new flow meter. The flow meter is to measure the mass flow rate of liquid flowing through a pipe. It is assume the mass flow rate (m) is a function of the pressure difference (AP)across the meter, diameter of the pipe (D), viscosity of the fluid (μ), and the density of the fluid (p). Using the dimensionless analysis, find the-groups for this case study.Q2:A) An experimental text program is being set up to calibrate a new flow meter. The flow meter is to measure the mass flow rate of liquid flowing through a pipe. It is assume the mass flow rate (m) is a function of the pressure difference (AP)across the meter, diameter of the pipe (D), viscosity of the fluid (μ), and the density of the fluid (p). Using the dimensionless analysis, find the 7-groups for this case study. UQ2:A) An experimental text program is being set up to calibrate a new flow meter. The flow meter is to measure the mass flow rate of liquid flowing through a pipe. It is assume the mass flow rate (m) is a function of the pressure difference (AP)across the meter, diameter of the pipe (D), viscosity of the fluid (4), and the density of the fluid (p). Using the dimensionless analysis, find the-groups for this case study.
- c) When small aerosol particles move through air or water, the Reynolds number is very small (Re < 1). Such flows are called creeping flow. The aerodynamic drag on an object in creeping flow is a function only of its speed, V some characteristic length scale, L of the object and fluid viscosity, µas indicated in Figure 11. Use dimensional analysis to generate a relationship for Fp as a function of the independent variables. The dimensions of Fp are MLT2. FD L Figure 11Ql: The viscosity in industrial measurement continue to use the CGS system of Lunits, since centimeters and grams vield convenient numbers for many fluids. The absolute viscosity () unit is the poise, I poise = 1 gtem. s). The kinematic viscosity (v) unit is the stohes, I stokes = 1 em /s. Water at 20C has u = 001 poise and also V= 0.01 stokes. Express these resalts in (a) SI and (h) BG tanits.The power P required for operating a pump depends on the diameter of the pump D, the pressure rise Ap across the pump, the fluid density p, the fluid viscosity and the Theorem, and D, Q and p as the repeating variables, the dimensionless group associated with μ is given by volume flow rate Q through the pump. Using Buckingham's μDªQbpº. Determine the values of a, b and c. 1. [0.99, 1.01 2. [-1.01, 0.99 3. [-1.01, -0.99 a= b = C=
- a) Vortex shedding is a common fluid flow problem across bluff bodies. The design of buildings and bridges take into account the analysis of vortex shedding phenomena to avoid the occurrence of resonance, where the natural frequency of the body matches the vortex shedding frequency. In this analysis, the following parameters are found to be important: velocity of flow (V), density of fluid (p), hydraulic diameter of the duct (D₁), dynamic viscosity of fluid (u), width of body (B) and the vortex shedding frequency (n). Using the method of repeating variables, find the non-dimensional relationship governing the phenomena.At a sudden contraction in a pipe the diameter changes from D, to D2. The pressure drop, Ap, which develops across the con- traction is a function of D, and Dz, as well as the velocity, V, in the larger pipe, and the fluid density, p, and viscosity, u. Use D, V, and u as repeating variables to determine a suitable set of dimensionless parameters. Why would ti be incorrect to include the velocity in the smaller pipe a sa nadditional variable?1. The thrust of a marine propeller Fr depends on water density p, propeller diameter D, speed of advance through the water V, acceleration due to gravity g, the angular speed of the propeller w, the water pressure 2, and the water viscosity . You want to find a set of dimensionless variables on which the thrust coefficient depends. In other words CT = Fr pV2D² = fen (T₁, T₂, ...Tk) What is k? Explain. Find the 's on the right-hand-side of equation 1 if one of them HAS to be a Froude number gD/V.
- The conduction heat transfer in an extended surface, known as a fin, yields the following equation for the temperature T, if the temperature distribution is assumed to be one-dimensional in x, where x is the distance from the base of the fin, as shown in figure: To Fin >X T(x) h,T Heat Loss d²T_hp (T-T) = 0 dx² ΚΑ dT dx = 0 Here, p is the perimeter of the fin, being 2R for a cylindrical fin of radius R; A is the cross-sectional area, being R2 for a cylindrical fin; k is the At x = 0: T = T₁ dT At x=L: :0 dx thermal conductivity of the material; T is the ambient fluid temperature; and h in the convective heat transfer coefficient. The boundary conditions are as follows: where L is the length of the fin. Solve this equation to obtain 7(x) by using Euler's method for R=1cm, h= 20 W/m².K, k = 15 W/m-K, L = 25 cm, T₁ = 80°C, and T = 20°C.Parts for each product Homework 1 n produce dryer plant Can for each product castiens Then each product is assembled in its dedicated washing and dryer A machines. Difterent are manufactured by press and motor ly sechon. The the monthly capacity of different sections are: washing machine or looo dryer machine Press section: 100 - Motor section: 1600 washing machine or 7o00 drjer machine machine assembly line: goo0 machine washing druer machine assembly line: 5000 machine washing 1, profit for each unct of washing and dryer machines is 270 and 300 respectively. Formulate a linear programming problem for Find ing how many washing and dryer machines should be produced many washing to maximize total plant's profit. 2.A A Post Company need to transfer 30000 boxes with two each truck presented of olifferent trucks. Chavactenistics problem for The table below. Formulate a linear programming each truck to optimum nunber of minimIze total Cost.Volumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V, pressure difference DP, fluid density r and viscosity m. a)Determine dimensionless P groups. b)A test is to be performed for a large pump that delivers 1.5 m3 /s of water from 40 cm diameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impeller is to be used. What flow rate should be used and what would be the pressure rise in model pump. Note: The model fluid is water at same temperature as the water in the prototype.