Manufacturing processes Q2: fill in the following blanks1-Form of programmable automation in which the mechanical actions of a machinetool or other equipment are controlled by a program containing coded2-Move the worktable to a programmed locationwithout regard the path taken to get to that location.3-Positions are defined relative to the previous locationof the tool.4-axes moves from right to left as you face the machine5- Open loop systems have no access to the real time data about the performanceof the system and thereforecan be taken in case ofsystem disturbance.6- Infeed back devices closely monitor the output and anydisturbance will be corrected in the first instance. Therefore high system accuracyis achievable.7-codes- specify program line number to executed by theMCU8-code is to travel the tool turret with rapid to thespecified point.9--drilling cycle is used for simple drilling/spot drillingoperations10-Cutter Compensation Cancel

As per our guidelines we are supposed to answer first three questions only.

Q2: fill in the following blanks 1-Form of programmable automation in which the mechanical actions of a machine tool or other equipment are controlled by a program containing coded 2- Move the worktable to a programmed location without regard the path taken to get to that location. 3- Positions are defined relative to the previous location of the tool. Oxer moves from right to left os vou face the machine

Q2: fill in the following blanks 1-Form of programmable automation in which the mechanical actions of a machine tool or other equipment are controlled by a program containing coded 2- Move the worktable to a programmed location without regard the path taken to get to that location. 3- Positions are defined relative to the previous location of the tool. Oxer moves from right to left os vou face the machine

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3: Write two G-code programs using the following figure where units are in inches. a. The first program should use absolute positioning, and b. the second program should use incremental positioning. P4 Finish (6, 4) P2 (1, 3) P3 (4.79, 2) P1 Start (-2, 1) Center (2.5, 1) -2
please send handwritten solution Q4 part c
(a) Summarize the following G and M code a. G41, G81, 691, G01, GOO b. M08, M30, M01, M06, M03 (b) Document three phases of writing a CNC program in the form of a block diagram. You don't have to write the actual CNC program.
5. Please give the definition and syntax for G00 and G28, and draw the toolpath and mark the passing point coordinate positions in XOY coordinate plane in the following two pictures separately after the code blocks being executed. G00 X6.0 Y3.0 Finish postion(6,3) Start postion (0,0) G91 G28 X0.0 Z2.0 Home postion (6,3) Start postion (0,0)
4. Consider a batch process of the conveyor oven illustrated in Figure 1. List all input and output process variables involved (binary and continuous), and draw the block diagram for the automation of the conveyor oven temperature and the connection schematic of the programmable logic control interface with process field devices. Motorized circulating fans Airflow (m/s) Electrical heating elements Heater voltage (volt) ww. Thermostat Thermostat ("C) ("C) 111111tt, Cake Cake Cake Cake Cake Cake II Travel direction Screw conveyor Stepping motor Figure 1: Cake conveyor oven.
For the following symbolic representation of a robotic manipulator arm: 1. Use the Denavit-Hartenberg (DH) convention to draw the correct coordinate frames on the diagram 2. Define the DH variables and draw them on the diagram 3. Construct and fill a DH table with variables for each joint/link.
David is working on her farming business and faces the challenge of watering her plants daily,which is a tedious and time-consuming task, especially under the scorching sun. The path shefollows for watering the plants is illustrated in figure 1.David's son has taken on the task of designing a prototype to automate the watering process forher. Figure 2 depicts the design, featuring a set of rods. The curved path represents David'stypical watering route, and the straight rod AB AB is confined to move along the path due to the pinsat its ends. Water sprinklers will be positioned at points A and B to efficiently water the plants.At the instant shown in figure 2, point A has the motion shown while its at the edge of the path.Determine the velocity and acceleration of point B at this instant.
1-Draw a figure that shows a negative rotation of a vector in 2D to illustrateyour answer to part (B-3)?2-In technical terms, what does Robot Manipulator Configuration mean? Note/ B-3 In which direction are rotations considered negative and state the handrule for this measurement?
please send handwritten solution Q4 part d
I need the full code of MATLAB
Q4/ write one command for each case: take data name is 'x' and file name is 'database' Import data form Excel sheet to MATLAB. 1. Export data form MATLAB to Excel sheet. 2. Save data as text file. MATLAB 3. Load data form text file. 4. Open and close file.
I want you to draw HGL& EGL For the first picture using the same method on the second picture