Q1/ In Sampling Theory solve the signal is = 3cos2000nt+5sin1500rt-10cos1400nt. %3D 1. Find Nyquest rate. 2. Find Nyquest interval. 3. Find minimum frequency sampling 4. Sketch the circuit and output waveform, message and pulse generator Note: • Connect the circuit by Simulink MATLAB and apply an amplitude Sine Wave is 2volt. In pulse generator the Period (number of samples):10 and the Pulse width (number of samples): 5. I need 2 wave

Q1/ In Sampling Theory solve the signal is = 3cos2000nt+5sin1500rt-10cos1400nt. %3D 1. Find Nyquest rate. 2. Find Nyquest interval. 3. Find minimum frequency sampling 4. Sketch the circuit and output waveform, message and pulse generator Note: • Connect the circuit by Simulink MATLAB and apply an amplitude Sine Wave is 2volt. In pulse generator the Period (number of samples):10 and the Pulse width (number of samples): 5. I need 2 wave

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A triangular pulse waveform is shown in figure by waveform analysis draw the component function and write the corresponding equation of the component function. ( Proper steps)
ument-460F8C6BE9D6- x 5-1.pdf CD Page view A Read aloud 1: Theory 1.1 Describe briefly a sinusoidal signal and ALL its properties. Give example with figures. ongingoring which is si +.
What is the difference between Signal to noise (S/N) &and Signal Pluse Noise To Noise
Q6. What is the purpose of harmonic standards? Provide a summary of comparison of IEEE and IEC standards. Write the purpose of the following international standards shown in Table- 2: [12] Table-2 Sr No 1 IEEE-18 Standards Description 2 IEEE 518 3 IEEE 519 4 IEEE 1159 5 IEEE P1433 6. IEEE P1453 7 IEEE P1564 8 IEC61000-3-2 9 IEC 61000-4-7 10 IEC 61642 11 IEC SC77A/WG9 12 IEC SC77A/WG2
9. PLOT. Plot the sine wave at frequency fm and the sampling signal at frequency fs1. Write a MATLAB program to take input both fm and fs1 and plot the curves mentioned above.,.
1. A rectangular pulse with a pulse duration , so in frequencydomain its form will be ............
Use multi-vibration circuits and create a signal generator that produces a square, triangular, and sinusoidal waveform with a frequency of 1kHz. Show work for theoretical layout. Also, use a switch for each waveform.
Show the capacitors, whether it is effective at low or high frequencsies Draw low frequency small-signal-equivalent circuit. AND LOWER corner is 82Hz frequency. Design the circuit. Draw the high frequency small-signal-equivalent circuit. AND UP-CORNER İS 172Hz frequency. DESİGN THE CIRCUIT.
The carrier frequency is 500 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y- axis is the amplitude of the AM signal. Determine the peak voltage level of the modulating signal in V. 3 2 1 -1 -2 -3 -5 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 Time (s)
At what frequencies will the output waveform be half-wave rectified? A full-wave rectified?
100 used to compand A companding system with u from 0V to 10 V sinusoid signal. Draw the characteristic of the typical system.
H.W: A resistor of resistance R=1000 2is maintained at 17 °C and it shunted by 100 uH inductor. Determine the ms noise voltage across the inductor over a frequency bandwi dth of: Ans: 182 x10° volt Ans: 9.22 x10 volt Ans: 2.34 x10 volt i) 15.9 kHz ii) i) 159 kHz 1590 kHz