Q1) Impulse response and the input of a discrete time LTI system are respectively h[n] = 28[n] – 8[n – 1] + 8[n – 2] and x[n] = 28[n] + 8[n – 1] – 8[n – 2]. (a) Plot the impulse response h[n] versus n (b) Plot the input x[n] versus n (c) Determine and plot the output of the LTI system, y[n] = x[n] * h[n] (d) Find and plot y[n] = x[n] + h[3n] Hint: Do the convolution and plot the results for steps for n = -2, –1,0,1,2, 3, 4.

Q1) Impulse response and the input of a discrete time LTI system are respectively h[n] = 28[n] – 8[n – 1] + 8[n – 2] and x[n] = 28[n] + 8[n – 1] – 8[n – 2]. (a) Plot the impulse response h[n] versus n (b) Plot the input x[n] versus n (c) Determine and plot the output of the LTI system, y[n] = x[n] * h[n] (d) Find and plot y[n] = x[n] + h[3n] Hint: Do the convolution and plot the results for steps for n = -2, –1,0,1,2, 3, 4.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A discrete-time signal x(n) is shown in the figure below, sketch and label carefully each of the following signals: a) x(n + 4) b) x(n- 1) c) x(n + 1)8(n – 4) d) x(n²) e) odd part of x(n) x(n) -10 12 3 Q2. 1/20
Q1) Impulse response and the input of a discrete time LTI system are respectively h[n] = 28[n] - 8[n – 1] + 8[n – 2] and x[n] = 26[n] + 8[n – 1] – 8[n – 2]. (a) Plot the impulse response h[n] versus n (b) Plot the input x[n] versus n (c) Determine and plot the output of the LTI system, y[n] = x[n] * h[n] (d) Find and plot y[n] = x[n] + h[3n] Hint: Do the convolution and plot the results for steps for n= -2,–1,0,1,2, 3, 4.
In Figure is given .. 10 - Ys) Ys) R() G{s) O A) there are not correct ans swers O B) multiple input and single output system (MISO) C) single input and multiple output system (SIMO) O D) single input and single output system (SISO) E) multiple input and multiple output system (MIMO)
Please give proper Circuit. Design a circuit with the following components; you can take any values. Vin is the input voltage. Vout is the output voltage. Rf and Cf are the feedback resistor and capacitor, respectively. R₁ and C; are the input resistor and capacitor, respectively.
29 - When the unit step function is applied to the system input whose block diagram is given below, the peak time of the output response is 3.1 s, and the settlement time is 5.0 s. T and a seen in the open loop transfer function are constant numbers. What is the damping rate of the system? calculate.A) 0.54B) 0.60C) 0.62D) 0.56E) 0.58
2) A discrete-time signal is shown in the figure below. Sketch and label carefully each of the following signals: a) x[n 4] b) x[3-n] c) x[3n] d) x[n]u[3-n] e) x[n - 2]8[n - 2] -2 -1 0 1 2 3 4 5
Q2: Draw the output waveforms (S, X, and Y) for the below sequential circuit by assuming the propagation delays of all the components that are shown in below figure equal to zero second. cik Cik DQ5
A system that satisfies the properties of superposition and homogeneity. Select one: a. Transfer function b. Linear c. Super position d. Signal flow e. Non linear W
Three EMG signals are required to be summed. The first and second signal, EMG1 and EMG2, are required to be scaled by a factor of -4, and the third signal, EMG3, by a factor of -2. Design an Op-amp based circuit to produce the required output operation.
a) Describe with the aid of suitable diagrams, the three types of stable output response to a step input produced by a second order system. b) The step response of a second order system is shown in Figure Q6. Magnitude 3 Result of Instruments Step Response 2.75 mmmm mm mm mm I 1.5 3 c) 2 1 ww www www m 1900 1999 1998 199988 0.5 1 Percentage overshoot Time to the first peak Damping factor, < Undamped natural frequency, wn 0 0 Find the: i) ii) Find the: i) ii) 2 Time (seconds) Figure Q6 2.5 3.5 4
Draw the output waveforms (S, X, and Y) for the below sequential circuit by assuming the propagation delays of all the components that are shown in below figure equal to zero second. S CIk clk A B
1. Consider an input x[n] and a unit impulse response h[n] of a discrete-time LTI system given by: h[n] = 38[n + 3] + 28[n+ 1] + 8[n] – 8[n – 1] + 28[n– 2] 1012 Determine and plot the output signal y[n] = x[n] * h[n] .