Q1/ Draw the normal stressdistribution over the crosssection on which the maximumnormal stress occurs. El =80000 MPa., E2=20000 MPaA10 kN/mM-20 kNMATERIAL10 MMBMATERIALMATERIAL 2100 MMMATERIAL 2-2 M--40 mmQ2/ the beam in Q1 (a) find the spacing required between Nails 1 (b) findthe spacing required between Nails 2, shear force per nails is 70 kN.50 mm16 mmNail 1-10 MM-140 mmNail 216 mm

The normal stress distribution over the cross section on which the maximum normal stress occurs.The…

Answered: Q1/ Draw the normal stress distribution…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >
The strain at point A on the bracket has components €g = 330 (10-6), e, = 560 (10-6), Yxy = -570 (10-6), e; = 0. Correct Part B Determine the maximum shear strain in the x - y plane. = 6.15x10-4 'in-plane Submit Previous Answers Correct Part C Determine the absolute maximum shear strain. (Figure 1) Figure < 1 of 1 vec -4 Yaa = 7.99 • 10 max Submit Previous Answers Request Answer X Incorrect; Try Again
help find the stress at segment BC, please
idity modulus doengro 17. A 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 90 MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is as aeqml 19WOL to da odt ons aasmos m noienet ni mioj по djiw YIVO P/24 F 12mm ↑ P/2 00 8mm 8mm
Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum tensile and compressive stresses in portion BC of the beam.(Take R=h=25mm). 4 kN 4KN -le A What B 300 mm 300 mm
2. For the truss shown below, determine the stress in members AC and BD. The cross-sectional area of each member is 850mm². [94.12, 78.42 MPa] A 000 RA B 70kN E 4 panels at 4m 16m = G 30kN H RH 3m
Beam I k 2 in.>| Beam II Each stringer = 2 in² 0.3 in. 3 in. 4 in. 0.3 in. 7 in. 0.3 in. 5 in. 6 in. Problem 2 For Beam II with the cross-section shown above M2 = 2000 in-lb and My = -1000 in-Ib. Determine: a) The angle of the neutral plane b) The value and location of the maximum tensile stress ox c) The value and location of the maximum compressive stress Oxx
The double - riveted joint connects two plates which are each 3.0 mm thick, and the rivets have a diameter of 4 mm., if the failure strength of the rivets in shear is 370 N/mm2 and the ultimate tensile strength of the plate is 465 N/mm?, determine the necessary rivet pitch b (mm) if the joint is to be designed so that failure due to shear in the rivets and failure due to tension in the plate occur simultaneously. Calculate also the joint efficiency n (%). 3 mm 4 mm diameter
a 36 ull AsiacelI اسئلة ت مواد.pdf > Q1: Find the normal stresses at sections A-A, B-B, C-C, and, D-D for the body as shown in figure (1). 60 KN B D=60mm D=150mm 82kN D=30mm 32kN 50KN 60KN B C D Figure (1) Q3: For the body shown in figure (2). Determine the normal stresses at sections A-A, B-B, C-C, and D-D A D 60KN 45 D=100mm D=50mm 80KN D=25mm 32kN 48KN A 45 60KN В C Figure (2) Q3 - Find the normal stress at sections A-A, B-B, C-C, and D-D for the member shown in Figure (3). A assume that the area of the member is (A mm²) , and the weight of member is (W kN ) cross sectional
Determine if the axial stress in nember CF if the area of each member is 75 mm^2. Indicate if T or C.
Two wooden members of uniform rectangular 150 mm cross-section are joined by a simple glued scarf splice as shown. Knowing that the maximum allowable shearing stress in the glued splice is 620 kPa, determine P. i. the largest load P that can be safely applied 1i. the corresponding tensile stress in the splice. 75 mm
The allowable stresses for the splice shown below are the following: 150 MPa. for shear of rivets, 1.35Fy for bearing, 0.6Fy for tension, and Fy = 250 MPa. Note: rivet holes are 2mm bigger than the rivet diameter, middle plate is 20 mm thick. 1. Find the diameter of rivets so that the joint capacity due to shear approximately equals that due to bearing. a. 25 mm b. 28 mm c. 30 mm d. 36 mm 2. Find the maximum safe P without exceeding the allowable shearing stress. a. 884.4 kN b. 938.3 kN c. 878.1 kN d. 848.2 kN 3. Find the maximum safe P without exceeding the allowable tensile stress. a. 579 kN b. 708 kN c. 495 kN d. 692 kN

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS