Q.1) A single phase load consisting of 5 2 in series with an inductance of 0.02297 His operated in a phase control mode with a of 90°. The source is 240 V RMS, 60HZ.Find:a) Draw the waveform of VTI and VR.b) Find the conduction angle (6).c) Calculate the RMS value of load current.d) Find the power factore) What is the minimum value of a for which phase control is in effet.f) Find the size of the first three terms in the Fourier series for the current.TZoom

“Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q.1) A single phase load consisting of 5 2 in series with an inductance of 0.02297 H is operated in a phase control mode with a of 90°. The source is 240 V RMS, 60HZ. Find: a) Draw the waveform of VT and VR. b) Find the conduction angle (8). c) Calculate the RMS value of load current. d) Find the power factor e) What is the minimum value of a for which phase control is in effet. f) Find the size of the first three terms in the Fourier series for the current.

Q.1) A single phase load consisting of 5 2 in series with an inductance of 0.02297 H is operated in a phase control mode with a of 90°. The source is 240 V RMS, 60HZ. Find: a) Draw the waveform of VT and VR. b) Find the conduction angle (8). c) Calculate the RMS value of load current. d) Find the power factor e) What is the minimum value of a for which phase control is in effet. f) Find the size of the first three terms in the Fourier series for the current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

Section [Section Upload answer sheets Find the following parameters of an ac voltage given by the equation v-100sin370t.Find RMS value,form factor, peak factor, average value and frequency. E Submission
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Why the frequency will double when we rectify an ac input to dc output at the ripple factor ?
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
Another name for the RMS value of current or voltage is ... O the effective value O the exact value O the true value O the reactance value
The temperature of a noninductive heater unit is controlled by a reactor. The heater unit and the reactor are connected in series across a 250 V, 60 Hz source. The voltage across the heater unit is 200 V. The voltage across the reactor is 100 V. The current in the circuit is 10 A. Determine: the power factor of the series circuit. the power factor of the reactor. the impedance of the reactor. the effective resistance of the reactor. the inductive reactance of the reactor
Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). Volvolt) 2- The ripple voltage. Vm = 12 V 3- The Vdc value. 4- The RMS value of the output voltage. V(p-P) = 0.1 V 5- The ripple factor. 6- The value of capacitor filter. (assume ideal diodes) T= 0.01 sec. t(sec.)
A chopper circuit drives an inductive load from 390 DC supply. Given the load resistance as 8 Q, the average load current as 23 A and operating frequency is 480 Hz. When the chopper is ON, 7 V is dropped. Calculate (a) conduction period (in milliseconds) (b) blocking period of the chopper (in milliseconds) (c) duty cycle of the chopper (d) draw the ON and OFF time period waveform (ii) Draw the circuit diagram of the single phase bridge rectifier which is used in two quadrant operation (RL load) and explain its operation.
A thyristor switched capacitor consists of: A. A fixed capacitance and a relatively small a relatively small surge limiting inductance B. A fixed capacitance and a relatively large surge limiting inducatance C. A variable capacitance and a relatively small surge limiting inductance D. A Variable capacitance and a relatively large surge limiting inducatnce
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
A 120 V, 60 Hz power source is connected across an 800 ohm resistance in series with an unknown capacitor. The voltage drop across the resistor is 102 V. Find the, a.) current of the circuit b.) impedance of the circuit c.) Capacitive reactance d.) capacitance value.